The range thermostat is also commonly known as a stove, oven, cooktop, or range thermal fuse. This thermostat protects your oven from excessive heating, and will shut the oven heat off if excessive heating is detected. This is a genuine part sourced directly from the original manufacturer. You may need to replace this part if your applian...Read morece will not heat properly. It is made of metal and is approximately 1 inch in diameter. This part is sold individually. It is recommended to order a spare, especially if you commonly use the self-cleaning function in your oven.
This temperature sensor, also known as a thermistor, is compatible with various makes and types of appliances. This thermistor uses electrical currents to detect the interior temperature of the appliance it is in and by working with the control board, the board adjusts the level of cooling or heating through its heating or cooling element...Read more, depending on what is needed. If your appliance is being improperly heated or cooled, the temperature sensor may be to blame, and can be tested with a multimeter to check for continuity to see whether it is defective. Check your user manual for exact placement of this thermistor and any diagnostic information.
This is a genuine OEM leveling leg for various models of LG ranges. This leg is used to stabilize and support the range, and if damaged, broken, or missing, will cause your range to rock back and forth. Installing this leg simply requires you to lift on the corner you are installing it under, and then screw it in place until your range is...Read more stable. This approximately 2-inch leveling leg is sold individually, so if your range has multiple legs that are broken or missing, consider how many legs you need to order.
A dual radiant heater supplies heat to a cooking area beneath a glass cooktop. Replacement may be needed when one zone does not warm, only the inner or outer section works, or the element has a visible break. Normal radiant burners cycle on and off, so cycling alone does not prove a failure. Check the control switch and connections first,...Read more then match the replacement by full model number, location, size, mounting points, and electrical rating. Disconnect the range at the breaker and confirm the circuit is dead before service. Handle sharp metal edges and the glass top carefully, and return every bracket, shield, and wire to its original position.
This transparent inner door glass is designed for LG range ovens and serves as a key component in maintaining heat insulation while allowing visibility into the oven during cooking. Made from heat-resistant material, it helps retain internal temperatures for consistent baking and roasting performance. Replacing a damaged or cracked inner ...Read moreglass restores the oven’s energy efficiency and ensures safe operation. This OEM replacement part is manufactured to fit specific LG models and is intended for use when the original glass is chipped, broken, or compromised. Installation typically involves removing the oven door, disassembling the inner panel, and securely fitting the new glass in place. Always confirm your oven model before installation to ensure compatibility.
This genuine OEM rack is placed inside your oven cavity, serving as a stable surface for your cookware. It measures approximately 25 inches by 17 inches. The wires can warp due to repeated temperature changes over time. Additionally, heavy or unevenly distributed loads can bend the rack structure, and accidental impacts during cleaning ma...Read morey result in broken rack supports, slides, or tubing. When this happens, it must be replaced. It is important to note that this rack is sold individually.
This sheath heater is a genuine OEM heating element designed for select LG oven and range models. Positioned at the top of the oven interior, it provides the heat necessary for broiling and, in some configurations, baking. Engineered to LG’s specifications, this component ensures consistent performance and even heat distribution. It repla...Read moreces older part numbers and is constructed for durability under high-temperature conditions. Common reasons for replacement include uneven cooking, lack of heat during broil cycles, or visible damage to the element. Installation should be performed with the appliance unplugged, and compatibility must be confirmed using the model number, as similar parts may vary in size and shape.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Harvey - For model number LRE6383ST
December 16, 2023
How do I identify the correct part number for the front left dual element burner on my LG glass top stove?
Hello Harvey, thank you for your question. The Dual Element is part PS7795472. Thank you and have a great day.
Oven is not heating. I will set it for 375 and although it tells me it is ready, the internal temperature is only 250. I have to set the temperature for 450 - 500 to get the internal temperature close to 375. I have changed the temperature sensor but this didn't correct the problem.
Hello Lyle, thank you for reaching out. Based on our understanding of the issue, we would suggest checking the control board, part number PS11773404, to solve the problem. Glad to be of assistance!
A few minutes after turning on the oven, it completely shuts off and trips the breaker. There are times when oven never shuts off. It shuts off more often than not. Stove top can be used without issue. Range is on its own electric source. Same one for years with no issue.
Hi Pablo, thank you for reaching out. Based on the description, the issue is with the safety thermostat, part number PS3530468. It shuts off the range if it overheats. We would suggest replacing the thermostat to fix the issue. We hope this solves your problem!
When using the oven, the stove will completely shut off after about 10 minutes of use. this does not happen all the time but 8 out of 10 times.
It does not turn off if the stove top is being used, only when the oven is on.
Hello Pablo, thank you for reaching out. According to our understanding, the issue is most probably with the relay control board, part number PS8751324. We would recommend replacing it to solve the problem. We hope this helps!
Hello, my dual element was not working properly, sometimes heating a bit but not well. We just replaced it and before putting it all back together checked the element. It went bright orange! Once together and back in place it is not working properly again. There is some heat that comes but not much. Any ideas??? Thanks
Hi Laura, thank you for your inquiry. Based on the description that you have provided, we would recommend making sure that you have installed the part correctly, and all the connections are intact. We would suggest reassembling the unit properly to fix the issue. Glad to be of help!
Was this helpful?
Thank you for voting!
Prev
1
2
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hammer 1, Glass range top and heating element 0
22 of 52 peoplefound this instruction helpful.
Richard from CHESAPEAKE, VA
Easy
30 - 60 mins
Screw drivers
Dropped a hammer on the range while removing a ceiling light. Viewed a How-To video on Google. Ordered the needed parts. Followed the steps from the How-To video. Reinstall was a bit tricky by myself - could have used an extra set of hands. I have a few words of caution: 1) Put something between the range top and range - like a
... Read moresheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet. 2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
Read less
Was this helpful?
Thank you for voting!
Plate Assembly Replacment
3 of 6 peoplefound this instruction helpful.
Norman from ST PETERSBURG, FL
Really Easy
15 - 30 mins
Pliers, Screw drivers
1. Unplug the stove (you will need 1 person to assist). 2. Remove the 3 assembly screw (Philips screws) located underneath the front of the assembly, near the oven door. 3. Raise the plate assembly to expose the heating elements (Take a photo of the positioning for installation reference). 4. Remove the wires connected th
... Read moree heating elements (unclip the connectors only). 5. Remove the holding clips from the heating elements (2 clips on each elements, the large element has 1 clip and 1 screw). 6. Remove the elements only (leave the wires in place). 7. Remove the Plate Assemble (save the 2 black rubber mounts located on the sides, the new assembly dose not come with replacements) . 8. Now your are ready to reinstall the Plate Assembly, so do the reverse and you should have no issues (check your photo for proper installation).
Read less
Was this helpful?
Thank you for voting!
PartsSelect substituted the part and it will not work
1 of 2 peoplefound this instruction helpful.
Rita from CROSS PLAINS, WI
Very Difficult
More than 2 hours
The repair person could not complete the job as the part sent is totally wrong for the appliance. The company has not responded to me email sent 12/30/23 and there is no way to leave a voice mail or ask for a call back, due to large call volume. A live representative does not answer the phone.
Please check your emails. You ask
... Read morefor feedback on repair, but obviously do not take time to check emails for issues. Because the error is on the part of PartSelect I requested an RMA to return an incorrect part. Please respond by sending a shipping label so it can be returned for a refund. I have submitted a dispute with the credit card company since your company is negligent in customer service. Please email RMA shipping label to [email protected]
My Orders
