The range thermostat is also commonly known as a stove, oven, cooktop, or range thermal fuse. This thermostat protects your oven from excessive heating, and will shut the oven heat off if excessive heating is detected. This is a genuine part sourced directly from the original manufacturer. You may need to replace this part if your applian...Read morece will not heat properly. It is made of metal and is approximately 1 inch in diameter. This part is sold individually. It is recommended to order a spare, especially if you commonly use the self-cleaning function in your oven.
This temperature sensor, also known as a thermistor, is compatible with various makes and types of appliances. This thermistor uses electrical currents to detect the interior temperature of the appliance it is in and by working with the control board, the board adjusts the level of cooling or heating through its heating or cooling element...Read more, depending on what is needed. If your appliance is being improperly heated or cooled, the temperature sensor may be to blame, and can be tested with a multimeter to check for continuity to see whether it is defective. Check your user manual for exact placement of this thermistor and any diagnostic information.
This is a genuine OEM leveling leg for various models of LG ranges. This leg is used to stabilize and support the range, and if damaged, broken, or missing, will cause your range to rock back and forth. Installing this leg simply requires you to lift on the corner you are installing it under, and then screw it in place until your range is...Read more stable. This approximately 2-inch leveling leg is sold individually, so if your range has multiple legs that are broken or missing, consider how many legs you need to order.
A dual radiant heater supplies heat to a cooking area beneath a glass cooktop. Replacement may be needed when one zone does not warm, only the inner or outer section works, or the element has a visible break. Normal radiant burners cycle on and off, so cycling alone does not prove a failure. Check the control switch and connections first,...Read more then match the replacement by full model number, location, size, mounting points, and electrical rating. Disconnect the range at the breaker and confirm the circuit is dead before service. Handle sharp metal edges and the glass top carefully, and return every bracket, shield, and wire to its original position.
This genuine OEM rack is placed inside your oven cavity, serving as a stable surface for your cookware. It measures approximately 25 inches by 17 inches. The wires can warp due to repeated temperature changes over time. Additionally, heavy or unevenly distributed loads can bend the rack structure, and accidental impacts during cleaning ma...Read morey result in broken rack supports, slides, or tubing. When this happens, it must be replaced. It is important to note that this rack is sold individually.
This sheath heater is a genuine OEM heating element designed for select LG oven and range models. Positioned at the top of the oven interior, it provides the heat necessary for broiling and, in some configurations, baking. Engineered to LG’s specifications, this component ensures consistent performance and even heat distribution. It repla...Read moreces older part numbers and is constructed for durability under high-temperature conditions. Common reasons for replacement include uneven cooking, lack of heat during broil cycles, or visible damage to the element. Installation should be performed with the appliance unplugged, and compatibility must be confirmed using the model number, as similar parts may vary in size and shape.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Norman - For model number LRE3061ST
July 7, 2022
I have an LG range oven not heating up was looking for the part number for the bake element
Hello Norman, Thank you for the question. This model has a Convection Element PartSelect Number PS7795453 and Broil Element, PartSelect Number PS12582157. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
I need replacement elements for both broiler and oven. Part number shows 5513 & 5514.
I can’t seem to find them separately. Please advise. Thank you
Hi Dale, thank you for reaching out. We have found that the heating elements for the oven and the broiler are the same, having part number PS12582157. Glad to be of assistance!
The oven and some burners do not turn on. I've cleaned the flexible ribbon. It works for a short while and goes out again. Can I replace the flexible ribbon? What part # is it?
Thanks for your help.
Hi Bill, thank you for reaching out. There are three harnesses listed under your model. The one is part number PS7791124, 2nd is part number PS3619651, and the third one is part number PS3619653. We hope that helps!
both the stove top or the oven elements heat up, I have replaced the thermostat , I am at a loss, need some help please
thank you
Hi Michael, thank you for your query. Based on the description that you have provided, we would recommend checking the following parts to fix the issue: terminal block, part number PS12742534, display control board, part number PS7792509, and main PCB assembly, part number PS12072598. We hope this solves your problem!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hammer 1, Glass range top and heating element 0
22 of 52 peoplefound this instruction helpful.
Richard from CHESAPEAKE, VA
Easy
30 - 60 mins
Screw drivers
Dropped a hammer on the range while removing a ceiling light. Viewed a How-To video on Google. Ordered the needed parts. Followed the steps from the How-To video. Reinstall was a bit tricky by myself - could have used an extra set of hands. I have a few words of caution: 1) Put something between the range top and range - like a
... Read moresheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet. 2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
Read less
Was this helpful?
Thank you for voting!
PartsSelect substituted the part and it will not work
1 of 2 peoplefound this instruction helpful.
Rita from CROSS PLAINS, WI
Very Difficult
More than 2 hours
The repair person could not complete the job as the part sent is totally wrong for the appliance. The company has not responded to me email sent 12/30/23 and there is no way to leave a voice mail or ask for a call back, due to large call volume. A live representative does not answer the phone.
Please check your emails. You ask
... Read morefor feedback on repair, but obviously do not take time to check emails for issues. Because the error is on the part of PartSelect I requested an RMA to return an incorrect part. Please respond by sending a shipping label so it can be returned for a refund. I have submitted a dispute with the credit card company since your company is negligent in customer service. Please email RMA shipping label to [email protected]
Read less
Was this helpful?
Thank you for voting!
Half the LEDs on my stove went out, the part fixed it.
2 of 7 peoplefound this instruction helpful.
Edward from FORT WORTH, TX
Really Easy
30 - 60 mins
Pliers, Screw drivers, Socket set
Unplugged the stove, took the top cover off, removed the old part and replaced it.
My Orders
