- Home
- LNC6766A71
- Instructions
LNC6766A71 Admiral Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
washing machine was making alot of noise
565 of 581 people
found this instruction helpful.
-
David from Boca Raton, FL
- Easy
- Less than 15 mins
-
Screw drivers, Wrench set
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again.
Was this helpful?
Thank you for voting!
One of the plastic hinge pins brroke
519 of 525 people
found this instruction helpful.
-
Allen from North Little Rock, AR
- Really Easy
- 15 - 30 mins
-
Screw drivers
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer jumping in spin cycle (white flakes under the washer)
292 of 306 people
found this instruction helpful.
-
David from Butler, PA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Wrench set
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the
... Read more
complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING (DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK) Install the new ring, tighten the screws and put the tub back in connecting everything back up and use the 6 new springs. It really isn't that hard to do.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The belt and pulley on the drive motor broke
154 of 193 people
found this instruction helpful.
-
Michael from Warminster, PA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the
... Read more
base, replace the pulley on the shaft (you may need to break or pry the old pulley off) install the new pulley making sure it is all the way up the shaft locking the tabs into the shat groove. Reinstallmotor to the base. To replace the belt, tilted the unit backwards to access the pulleys from the bottom and installed.
Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.
Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.
Read less
Was this helpful?
Thank you for voting!
Load Grinding/Rubbing Noise in Rinse and Spin Cycles
139 of 155 people
found this instruction helpful.
-
Doug from Port Richey, FL
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
First unplug the washer for the electrical outlet. You will need to tip the washer back to get to the bottom of the machine. There you will see the belt that drives the transmission and the water pump from the motor. Remove the belt and set it to the side. Then you will need to gain access to the top side of the machine by gently using
... Read more
a screwdriver to pry the front of the top up off the front panel on both sides then hinge it back out of the way. Use a nut driver to remove the two screws on the inside edge of the front panel and remove the front panel. Once the front panel is off you will see the water pump on the right hand side as you face the front of the machine. Remove the hose clamp on the water pump with the flat head screw driver or nut driver and use a pair of pliers to remove the compression clip on the water pump. Remove the 4 bolts holding the water pump in place. Reverse the entire process to put it back together. This job was very easy and I was only without a washer for 2 days because of partselect.com.
Read less
Was this helpful?
Thank you for voting!
Water would overflow from the top of the machine
78 of 100 people
found this instruction helpful.
-
Peter from Manorville, NY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
The repair was very easy. Remove a few screws, switch wiring one at a time so I put them in the correct position and replace. The hose replacement was easy at the swicth but a little more difficult at the lower end of the tub due to limited space. Overall an easy job and now it works fine!
Other Parts Used:
Was this helpful?
Thank you for voting!
broken motor pulley
64 of 78 people
found this instruction helpful.
-
leighton from staten island, NY
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
i removed the plastic cover.then i disconnected the harnest.i then removed the 2 screws and took the motor out. i took a hack saw blade and made a mark in the old pulley. i then took a screw driver and put it in the crack and tapped on it and the old pulley fell apart. i then put on the new pulley and reconnect the motor. i then reconnect
... Read more
the belt.my washer is working great.it was so easy and i save myself some money in the process.
Read less
Was this helpful?
Thank you for voting!
The unit was leaking during agitation and spin cycle
58 of 62 people
found this instruction helpful.
-
Dan from Grain Valley, MO
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
I had to remove the back lower panel with a nut driver (approximately 8 screws) as well as the front panel which is removed by poping the top of the unit removing 2 screws and swinging the panel down and lifting off.
Remove the bleach fill cap (pry off). You'll need a long extension on your ratchet to remove the bolt holding on the ... Read more agitator. Next remove the inner tub which is held on by 4 bolts. The outer tub is a bit more difficult. You will need to remove all 4 shoulder screws from the top as well as the six that anchor it to the spring assembly around the bottom skirt. Since it was 7 years old I had to muscle the outer tub and rotate it to get around the inner tub transmission flange.
I'm not sure which of the 3 parts were leaking so I ordered and replaced all 3.
I don't know if it was necessary but I scraped and cleaned the aluminum flange plates where the gaskets seated.
At this point it was easy to replace the tub to housing gasket and tub/housing seal.
During reassembly I also replaced the basket to centerpost gasket.
I went with standard delivery but got the parts the next day.
Remove the bleach fill cap (pry off). You'll need a long extension on your ratchet to remove the bolt holding on the ... Read more agitator. Next remove the inner tub which is held on by 4 bolts. The outer tub is a bit more difficult. You will need to remove all 4 shoulder screws from the top as well as the six that anchor it to the spring assembly around the bottom skirt. Since it was 7 years old I had to muscle the outer tub and rotate it to get around the inner tub transmission flange.
I'm not sure which of the 3 parts were leaking so I ordered and replaced all 3.
I don't know if it was necessary but I scraped and cleaned the aluminum flange plates where the gaskets seated.
At this point it was easy to replace the tub to housing gasket and tub/housing seal.
During reassembly I also replaced the basket to centerpost gasket.
I went with standard delivery but got the parts the next day.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
washer would agitate, pump, but not spin
62 of 74 people
found this instruction helpful.
-
steve from lebanon, OH
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
First I unplugged it, then removed the agitator and tub assemblies, then I tipped it back and removed the belt and pully and thrust bearings. After reading on here I learned the brake would stick and after installing the thrust bearing kit I found out I couldnt fit in the shims. That led me to believe the brake was siezed inplace so i cou
... Read more
ldn't fit in the parts. I removed the thrust bearing kit and removed the transmission assembley. I took apart the brake and found the two pieces had siezed together, after I got them apart I sanded both peices and lubed the shaft with high temp silicone like you would use on a cars brake system. I put the brake back together, BE VERY CAREFUL THE SPRING HAS ALOT OF PRESSURE! I then put the transmission back in, reinstalled the thrust bearing kit and it fit great. I put in the tub and agitator and washed clothes.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Loud noise during the spin cycle
80 of 136 people
found this instruction helpful.
-
John M from Saint Paul, IN
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Repair was made by viewing on line video and owners manual. Once the machine was apart, the brake spring was the only tricky patr. Under a lot of pressure so be cautious. old bearing was removed and the new bearing installed. Machine reassembled. no issues.Thanks !!!
Was this helpful?
Thank you for voting!
Water Dripping into the tub
54 of 61 people
found this instruction helpful.
-
William from McKinney, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Unplugged the electrical plug from outlet. Disconnected the water hoses after I turned off the water supply. Using a screwdriver, popped up the washer top. Using needlenose pliers, I removed the wired from the defective valve, and removed the hose that feeds water into the tub. From the back of the washer, I removed th screw holding th
... Read more
e valve in place. Reaching inside the washer, I removed the defective valve. I attached the electrical wires and hose to the new inlet valve prior to installing the valve. After installing the valve in place, I inserted the screw in the the valve from the back of the machine. I then reattached the hot and cold water hoses, closed the top of the washer, turned on the water supply, and plugged the machine back into the electrical outlet. I turnd the machine on, then off, and the water was no longer dripping into the machine. Problem fixed.
Read less
Was this helpful?
Thank you for voting!
washer would agitate, drain, but would not spin
44 of 49 people
found this instruction helpful.
-
michael from mountain home, ID
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
I put the washer on the spin cycle and could see that the tub wanted to move. While it was trying to spin I leaned the washer forward and saw that the motor was spinning and the belt was turning, but the tub wasn't. Did some reading and it was the thrust bearing. I ordered the part and replaced them (very easy, follow the directions that
... Read more
come with the set). After install, the tub would spin.
Read less
Was this helpful?
Thank you for voting!
The agitator auger was broke.
50 of 68 people
found this instruction helpful.
-
Donna from Borger, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
All i did was remove the screw, took off broken agitator auger and replaced it with the new one and put the screw back in and was done in about 5 mintues. Super easy.
Was this helpful?
Thank you for voting!
Intermittent problem with lid switch, no high speed spin/pump out
48 of 63 people
found this instruction helpful.
-
Linda from La Porte, IN
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Disconnect power, unsnap and raise machine top cover w/lid, remove old switch - two screws under lid, taking care to not drop loose actuator lever into machine. Remove control panel back and disconnect switch wire connector. Intall new switch, taking care to not drop loose actuator lever into machine, connect switch wires inside control
... Read more
panel. Replace panel cover and lower machine top cover w/lid and snap into place, reconnect power, verify operation...
Read less
Was this helpful?
Thank you for voting!
washer would not spin water out in heavy loads
43 of 48 people
found this instruction helpful.
-
marcus from mansfield, TX
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
You do not have to remove any water lines to do this repair. Just unplug the machine from the electric outlet and tip it up on its back to make the repair. I removed the old belt and parts per the instructions. The new kit does not look like the old one. Make sure you mark the minimum and maximum marks with a sharpie on the plastic pul
... Read more
ley before intalling it. This will help line up the cam bearing to test the spin cycle. The repair kit says to use the thickest washer but mine would not fit on so I used the thinner washer. Keep the other washer so that in the future if the plastic part wears down and you have spinning problems again you can replace it with the thicker washer. Also make sure you buy a new belt and replace the belt. I loaded it up with a full load of jeans and it works great.
Read less
Was this helpful?
Thank you for voting!