EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

LER331DS0 Frigidaire Dryer - Instructions

All Instructions for the LER331DS0
121 - 135 of 566

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Heat, Dryer Runs, But Right Side Of Timer Would Not Advance, Left Timer Would
2 of 2 people found this instruction helpful.
  • STEPHEN from Nashville, TN
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
I used the percentage scale on this website to try and determine the likely cause. After reading several sites, I couldn't make sense of the timer not working on just one type cycle. When I got the dryer drum off, I could plainly see that one of the heater coils was broken. They get heat stressed and break down over time and a hard shak e probably finished this off. This unit is 5 plus years old. It was Saturday and I had no heater, so I actually found it at a local parts supplier. Also replaced the drum bearing and the bearing cup in the rear along with the heater. BTW, a new heater comes with a HIGH thermal switch attached to it so don't buy it extra. The bearing cone also comes with a new bushing in the pack. I DID use the Thermal Limiter that I order from the site because I was already in there. Everything works great now. I may have gotten most off my parts elsewhere but this site was the biggest help of them all. I will definitely be back here again.
Was this helpful?
Thank you for voting!
Drum would not spin
3 of 5 people found this instruction helpful.
  • garland from Morganton, NC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
After unplugging the dryer, disconnecting it from the vent, and moving into an open work area, I popped the top open with the blade of a screwdriver, disconnected the two wires that connect to the door switch, then lifted the front panel (with the door) up and away from the drum. Next, I lifted the drum out of the worn rear bearing assem bly and lowered it into the dryer in order to release tension on the belt. I then removed the entire drum by carrying it forward and out of the way. I then removed the old bearing assembly, which was loose and covered with metal dust. After cleaning the area with a dry cloth to remove the old grease and metal dust, and vacuuming all the lint off *everything*, I installed the new bearing assembly with a 5/16" nut driver, being careful to position the provided ball-bearing between the plastic bearing assembly and the outer clip. The little ball-bearing is very important, as it is the drum's only path to ground, and prevents the build up of static electricity as the drums spins. I then filled the new bearing assembly with the provided grease. Everything is easy up to this point, but the difficult part for me was removing the old hub from the drum and re-attaching the new one. It is held on by three screws and they become seated very tightly. After loosening them and removing the old hub from the drum, attaching the new one prvoed difficult as well, as the screw-holes in the new hub are not threaded to fit the screws. The screws muct be forced to cut a thread as you install them, which requires a great deal of force. After installing the new hub and putting the new belt (pruchased separately) around the drum, the next step is to reinstall the drum by lifting it in through the front of the dryer and positioning the new hub over the new bearing assembly and pressing it down into place. It will gently "snap" into place as it seats. Then, on the back side of the dryer, I removed the vent panel by removing the two screws that hold it in place and positioned the new drive belt (loosely dangling around the drum) over the motor's drive wheel and behind the sring-tensioned idle arm. Then it is a simply matter to reinstall the front panel by genly lifting the drum and sliding the door opening inside it, then reseating all the little clips that hold the front panel in place. I then pressed the top back into place, reconnected the vent hose, plugged it back in and checked for operation. My fifteen year-old dryer now works like new!
Was this helpful?
Thank you for voting!
Loud Squealing
2 of 2 people found this instruction helpful.
  • William from Hudson Falls, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Remove top panel with large flat screwdriver and 2 screws in back.Remove bottom panel with 2 screws.Release belt tensioner and remove belt.Remove 3 screws in center of drum inside.Remove drum. Remove rear bearing by pulling up on assembly.Replace all parts in reverse order.
Was this helpful?
Thank you for voting!
Very noisy
2 of 2 people found this instruction helpful.
  • Cherry from WATERVLIET, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Replaced rear drum bearing, drum support bearing & drum belt. Still very noisy. Will order new motor & see if that does the trick.
Was this helpful?
Thank you for voting!
Broken Timer Knob, Broken Start Knob, Possibly Damaged Start Switch
2 of 2 people found this instruction helpful.
  • JEREMY from JONESBORO, GA
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
First, removed the metal access panel by removing screws. (EASY)
Second, pressed the timer knob onto the timer shaft. (EASY)
Third, mounted the start switch to the mounting surface. (A BIT DIFFICULT)

Fourth, pressed the start knob onto the freshly mounted start switch. (EASY)

Fifth, replaced the metal acces s panel by replacing screws. (EASY)

Dryer now functions like new.
Was this helpful?
Thank you for voting!
May not have to take out the whole drum to replace the limiter!
2 of 2 people found this instruction helpful.
  • Timothy from CRANBURY, NJ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
After lifting the dryer top and finding the location of the thermal limiter on the back of the dryer, where it is difficult to get at, I carefully cut through the dryer cabinet with the multimaster on three sides to form a 'flap' upon which the limiter was mounted. By prying this flap open from the back, the two wires and two screws are e asily accessible to replace the limiter, without having to remove the whole drum. Afterwards, I just bent the flap back into place and taped the seams. If it ever blows again, the fix will take all of about two minutes.
Was this helpful?
Thank you for voting!
Dryer not heating
2 of 2 people found this instruction helpful.
  • Steve from COVINGTON, KY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
UNPLUG DRYER (this is key) Removed the top of dryer. used screwdriver and pliers to remove two screws and electrical connections then reinstalled new part stick the magnet behind the part to the back of the dryer to help control the small screws.
Was this helpful?
Thank you for voting!
dryer wouldn't heat
3 of 5 people found this instruction helpful.
  • billy from millsboro, DE
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
remove top of dryer by prying with large screwdriver to snap back clips that hold it on remove two screws on both sides that hold the door . remove door then remove belt from dryer tub. (to remove belt take the back panel near floor off with screwdriver and lift pullie up that hold belt. )then lift tub upward to disconnect it from it's se at; pull it straight forward to get to the heating element.un bolt it with screwdriver and disconnect the sensor and put new heat element in
Was this helpful?
Thank you for voting!
Dryer would not turn on, no power. Since i already have replaced thermal limiter switch, i knew exactly what to do and also how to shorten installation
2 of 2 people found this instruction helpful.
  • Daniel from SAN ANTONIO, TX
  • Very Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Remove 2 screws from back of unit, remove top by lifting and pulling up, set aside. Using pliers,needle-nose, remove the 2 wires from switch, then using a magitized philips screw driver, remove 2 screws holding switch to back of unit, replace switch, reassemble everything. 20 minutes, boom, ur done, dry some clothes now
Was this helpful?
Thank you for voting!
2 of the dryers knobs had broken off
3 of 5 people found this instruction helpful.
  • Ann from Inglis, FL
  • Really Easy
  • Less than 15 mins
I ordered the knobs at less than half the price I paid before from the retailer. The knobs came in the mail very quickly. I took the knobs from the package and put them on. Easy repair, and I was especially happy with the ease of ordering and quick delivery.
Was this helpful?
Thank you for voting!
Door handle broke and came off.
2 of 2 people found this instruction helpful.
  • Elizabeth from Mentor, OH
  • Really Easy
  • Less than 15 mins
Simply popped it back into place, careful not to break the new handle.
Was this helpful?
Thank you for voting!
replaced knob, perfect fit and match
2 of 2 people found this instruction helpful.
  • Paul from Beverly Hills, FL
  • Really Easy
  • Less than 15 mins
just pushed new knob on.
Was this helpful?
Thank you for voting!
old knob was strip
2 of 2 people found this instruction helpful.
  • DENISE K from cleveland, OH
  • Really Easy
  • Less than 15 mins
remove old knob and washer that was on it put new knob on and turn the knob dryer was save
Was this helpful?
Thank you for voting!
It got lost...
2 of 2 people found this instruction helpful.
  • Kevin from Rome, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was very, very simple... I just had to find two screws ( that were not included)...no problem...
Was this helpful?
Thank you for voting!
Door catch broken
2 of 2 people found this instruction helpful.
  • TJ from SCOTT DEPOT, WV
  • Very Easy
  • Less than 15 mins
Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!
Was this helpful?
Thank you for voting!
All Instructions for the LER331DS0
121 - 135 of 566