L9875XRB Norge Wall Oven - Instructions

Easy in and out, just two screws and two wires. Only additional work was that my oven had female spades on the wires and so did the new element. Took a couple of extra minutes to change out the spades on the oven connections. Then it was slide the connectors together, re-attach the two holding screws and the oven was fully functional.
... Read more />
First replacement element came in bent, Parts Select shipped and replaced it immediately!

Once I saw the spring clips on the new door seal, it was easy to understadn how to remove the old seal and install the new one. Looks nice !

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh ... Read more t bulb in was not the problem.

Removed screws on each end of element, pulled off spade connectors, did everything in reverse for new element.

The only notable fact was that the old element was hot, as in carrying AC current, despite the stove being off and it being broken, and I found out the usual way.

First off, because of weather delays, it took FedEx 8 days to deliver part, finally had to drive 3 miles out our road to meet driver.
The connectors were females on the new part as were the connectors in the range. Had to cut off oven connectors and replace with males. Fortunately, I had the connectors (not supplied) and knew how to ... Read more attach them.

First I remove th screw that held the element in place then I pulled the element out and disconnect the wires. Then I replace the new element, I connected the wires back then I put the screws to hold the element.

Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order

Unfortunately, neither the new bake element or sensor fi ... Read more xed the problem, so I just ordered the more expensive control board -- hope that does it.

Screwed in light bulb and glass protector

Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.

Very simple process of diagnosing. Toughest part was finding the part. Part Select mad it very easy, inexpensive and great service and delivery right on time. What a great site. Will always come here first.

I ordered the only part that looked like it would fit. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. But the new replacement had the wrong ends to fit right. I was going to email you back to see if there were other options for me, when a frien ... Read more d came by and said he would just replace the oven connecting ends and then it would work. Luckily he had extra little ends at home, came over and replaced the ends, cutting the old ones off of the oven side. He wire stripped the wire, attached the new ends and crimped and then reattatched the whole heating element. Without his know-how, I would have had to have a repair man come and do the same thing for me, or go buy a new stove.....but it is simple when you know how!! It would have been helpful to me, to have the description of the ends of the new element I was buying..... whether it was male or female... but it is fixed now, thanks to my friend. A steak dinner was cheaper than a repair man!!!!

Husband got on partselect.com and read reviews, we ordered a long oven sensor kit. When it came in the mail, I took it out and look at it, decided I could probably switch the part.... and so I did. Easy Breezy ... and it worked well

I followed the instructions that were posted on the web site for the replacement of the element. I found everything exactly as described in the procedure. I disconnected the two screws that held the old element, removed the old element, inserted the new element and replaced the screws. I turned the oven control on and the element heate ... Read more d up. Everything has been working just fine.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Took four screws out, pulled old one out and disconnected two wires and waited for new part to be delivered. installed part in one minute. I had the same thing happen 5 years ago and the repair person charged me $150. This time it cost me $40 .