- Home
- KWS839ZAS0
- Instructions
KWS839ZAS0 Frigidaire Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
replace broken drive belt
285 of 320 people
found this instruction helpful.
-
rodney from fairfield bay, AR
- Really Easy
- 15 - 30 mins
-
Screw drivers
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub p
... Read more
ulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.
Read less
Was this helpful?
Thank you for voting!
Clicking due to agitator dogs slipping
81 of 102 people
found this instruction helpful.
-
BRIAN from UPLAND, CA
- Really Easy
- Less than 15 mins
-
Socket set
One bolt (after removing the fabric softener dispenser and a water tight cover you will see it). Remove the bolt and slide it straight up and then it's the reverse to put in the new one. Very simple repair and very inexpensive if you willing to do it yourself.
Was this helpful?
Thank you for voting!
Lid Lock Assembly broke
76 of 95 people
found this instruction helpful.
-
Jenessa from Tacoma, WA
- Easy
- 15 - 30 mins
-
Screw drivers
The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would
... Read more
need to pay a repair person to do!
Read less
Was this helpful?
Thank you for voting!
Agitator Drive Block wore out
69 of 115 people
found this instruction helpful.
-
James from Somerville, MA
- Really Easy
- Less than 15 mins
Removed fastening screw and Agitator. Removed and replaced Agitator Drive Block. Replaced and fastened Agitator. Done in 5 min.
Ordered part around noon. Shipping was 3-5 days. Part arrived in LESS than 24 hours.
Very happy camper here!
Ordered part around noon. Shipping was 3-5 days. Part arrived in LESS than 24 hours.
Very happy camper here!
Was this helpful?
Thank you for voting!
washing machine will not drain or spin
41 of 49 people
found this instruction helpful.
-
Heath Harris from Arnold, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
removed upper cover, removed front cover, tested switch with digital VOM, removed and replaced!
2 screws, 4 wires! saved over $100 when compared to a bill from a repair service!
fast shipping too! will recommend others!
2 screws, 4 wires! saved over $100 when compared to a bill from a repair service!
fast shipping too! will recommend others!
Was this helpful?
Thank you for voting!
Broken agitator in washer
27 of 35 people
found this instruction helpful.
-
Elliott from Orinda, CA
- Easy
- Less than 15 mins
-
Socket set
5 mins. Take off fabric dispenser. Pop off cover underneath. Unscrew bolt. Pop off agitator. Put on new one. Screw back down. DONE :0)
Was this helpful?
Thank you for voting!
washer machine wouldn't move
23 of 29 people
found this instruction helpful.
-
Luis from Riverside, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
first removed the 2 screws disconected the terminals, installed new switch connected wires back and test washer and it worked like new, i put a Jumper to get the washer to work while i got the parts. Also i received the parts in 24 hrs. Thank You.
Was this helpful?
Thank you for voting!
the belt was all worn out , it make a lot of noise
26 of 38 people
found this instruction helpful.
-
CARLOS from BEALETON, VA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
i took out the two back screws lift the top.
took the two bottom front screws , lifted andtook off the front panel.took off the old belt an intall the new one in a circular motion put the panel and top back on and done.
took the two bottom front screws , lifted andtook off the front panel.took off the old belt an intall the new one in a circular motion put the panel and top back on and done.
Was this helpful?
Thank you for voting!
The upper part of the agitator wasn't working.
21 of 27 people
found this instruction helpful.
-
Bob from Estes Park, CO
- Really Easy
- Less than 15 mins
-
Socket set
I removed the bolt holding the agitator in the tub and lifted the agitator out. There seemed to be a part near the top that was not engaging. I decided to order a replacement to see if that was the problem (my local repairman had guessed the problem was in the transmission and said I should just replace the machine.) I ordered the part on
... Read more
line and it arrived in only two days. I was very happily surprised by the speed with which I received the part. I put the new agitator in, tightened the bolt and ran a load of clothes. All worked perfectly
Read less
Was this helpful?
Thank you for voting!
Washer wouldn't spin
22 of 33 people
found this instruction helpful.
-
KELLEY from KANSAS CITY, MO
- Easy
- Less than 15 mins
-
Screw drivers
Received lid lock within 24 hours, fixed washer within 10 minutes...up and running. Thanks.
Was this helpful?
Thank you for voting!
No Final Spin Burning Smell
17 of 18 people
found this instruction helpful.
-
NELSON from MAYWOOD, IL
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Removed 2 screws at bottom of the front panel - removed front panel by sliding the panel down about 1/2 inch and then away from the appliance- v belt is removed by pushing the tensioner pulley to remove tension from the belt and turning the pulley untill the belt is removed instalation is a simple reverse of the process. I did't have a
... Read more
repair manual so every step was trial and error untill I was able to complete the repair.
Read less
Was this helpful?
Thank you for voting!
Burning smell, lots of hi-pitched squeaking
17 of 19 people
found this instruction helpful.
-
Heather from Stephenville, TX
- Easy
- 15 - 30 mins
-
Screw drivers
I got online and figured out exactly how to take off the front of the washer and then how to replace the belt. It was so easy. The part itself arrived much sooner than predicted. It fit perfectly and my washing machine is now running smoothly and quietly.
Was this helpful?
Thank you for voting!
Washer machine would fill up with water and not spin and drain
18 of 25 people
found this instruction helpful.
-
MARC from MANALAPAN, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Happened to slam the lid by mistake and the washer started spinning. Recognized the lid lock was working haphazzardly. Also, there was a burning type odor coming from the switch. So I lifted the lid top and disconnected the switch from the lid by unscrewing 2 screws and 4 wires. When I received the new switch, I reinstalled it with 2
... Read more
screws and reconnected the 4 wires.
Read less
Was this helpful?
Thank you for voting!
agitator not turning on top, clothes not clean
18 of 29 people
found this instruction helpful.
-
Scott from Palmyra, TN
- Easy
- Less than 15 mins
-
Socket set
ordered part from parts select, it was the wrong part,( all my fault) they refunded part upon return and sent the new part, the return was easy and prompt, new part arrived, 15 minutes wife was washing and happy again, and we all know, happy wife happy life, thanks part select!!!
Was this helpful?
Thank you for voting!
washer belt broke
11 of 12 people
found this instruction helpful.
-
Carl from Boxford, MA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
followed the instructions on a blog
Was this helpful?
Thank you for voting!