KUIS185G KitchenAid Ice Maker - Instructions

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only ... Read more swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

I removed the cutter grid and unplugged the light bulb and wire heating plug ins. I slid the front cover plate off the cutting grid and loosened the screws on the front of the cutter grid and unthreaded the broken, top grid wire, leaving the bottom wire in place as it was in tact.
I then threaded the new wire through the cutting gri ... Read more d frame starting in the center and threading right and then left. While the threading was not difficult, the wire was easily kinked. The process up to this point was only 15 minutes or so.

Once it was completely threaded, I worked for a couple of hours trying to smooth and straighten the wire so that is was somewhat taut and straight enough to create symetrical ice cubes.
My frustration came in pulling on the wire from the center point to each outside ending point where it was to be wrapped around the screw and the screw tightened back down. The wire was fragile enough that it would break, by the time I was finished I barely had enough wire left to touch the screw let alone hook around the screw.
After 3 or four days of successful opperation, the grid quit cutting again. As I took it apart, it was obvious that the weight of the ice was enough to pull the wire, that was already too short, away from the screw. I refastened it again, but think it is unlikely to hold.
If it won't hold, I would be hard pressed to purchase another wire. I may bite the bullet and purchase the entire grid mechanism with the wires already installed. Even though the cost of the entire grid mechanism is $200 more than the purchase of another wire, it may well be worth the ease of installation!

I removed the three nuts that hold the old pump, easy. Next step was to replace with the new pump, tricky, because it goes real deep in the machine and my arms barely reach it.
After several attemtps, I finally reached one screw and bolt it immediately. Rest was piece of cake.
What I liked most, is that you don't need to do any ... Read more wiring connections, because it uses a simple plug-in connector that goes in at the same time when you bolt the new pump.
What it surprised me, was that my machine it's over 20 years old, and the new replacement water pump it's the very same design !!!
Last night I fixed it, and today I'm enjoying again fresh ice.
One plus for PartSelect : I inherit this machine and didn't have an Installation & Operation Manual,and PartSelect have it On-Line, so I printed it, and I believe I'm ready another 20 year period of fresh ice!
Thanks a lot PartSelect !!!

This is a stand alone ice maker that uses a standard water valve. When the valve fails (usually stuck open) the water never chills enough to freeze because water is constantly flowing into the hopper. The valve is in the very front. Remove the front panel. Turn of the water supply and disconnect the valve. Replace the valve and turn on th ... Read more e water. Let the machine run through 1 cycle before the new valve will dispense water. Done.

Easy to do.!

First I removed the cutter grid assembly by removing two screws. Also disconnect the wire that powers the grid. Once on the bench, simply remove the broken cutter wire. String in the new wire, starting at one end and working back and forth to the other end. Tighten the terminal screw on the first end, and then "strum" the wires, one a ... Read more t a times, pulling the wires taught. Pull the excess wire thru the second terminal, until all wires are taught, with equal tension. Tighten the second terminal screw, and cut off excess wire at both ends. Re-assemble cutter grid into Ice Maker.
Problem solved!

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

remove tray from icemaker by removing 2 screws and disconnecting 2 electrical connectiona. Remove broken wire and restring new wire. Reinstall tray.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Removed the grid. Removed the existing top to bottom wire. Restrung the grid with the new wire. Then, it cut ice just fine-better than new. Note: wire provided is only sufficient to rewire side to side or top to bottom, not both. If you need to do both, you'll need 2. Yes, lots of money for a few feet of wire.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

The post I read said start at the middle and work your way out towards the left and right. This was incorrect. All I did was secure one end to the torx screw and tighten it down. I then slowly pulled the wire as tight as I could around each insulator, going slow so as to not kink the wire (very easy to do). Once I was at the other tor ... Read more x screw I used a pair of linesman plyers to gently tug each wire tighter, I needed an extra pair of hands to hold the grid down. Once everything was tight I wrapped the last torx screw and tightened. Here's what no one is saying, you will not get the wire as tight as it originally was but that's ok. After I got everything reinstalled the ice maker is making ice like a champ.

removed broken wire, replaced with new wire and screwed the 6 tensions screws to tighten the grid wire.