Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUIC15PRTS3 > Parts

KUIC15PRTS3 KitchenAid Ice Maker - Parts

All parts for the KitchenAid Ice Maker KUIC15PRTS3

Below is a list of all parts for the KitchenAid Ice Maker KUIC15PRTS3. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the KUIC15PRTS3
1-14 of 142
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$87.13

Condenser Fan Motor Kit

This condenser fan motor kit includes a motor, fan blade, wire harness, and screws. Used in a refrigerator, the condenser fan motor moves the condenser fan blade to direct and move...

$62.84

Recirculating Pump - 60Hz

A recirculating pump is used with standalone ice cube makers. It circulates the water over the top of the evaporator plate, which produces a layer of ice that is then broken down into ice cubes. If you notice that your ice maker is no longer producing ice or there is no water flowing over the cooling plate, this could be due to the recirculating pump not working. Be sure to keep the pump clean and free of build-up. This pump is 5.75 inches in length, 4.75 inches in width, 4.25 inches in height and weighs 0.81 lbs. This is a genuine OEM appliance part that comes directly from the manufacturer.

$137.02

Ice Cutter Grid Complete Assembly

If your freestanding ice maker is not producing ice properly, the ice cutter grid assembly may need replacing. The cutter grid is located within the main unit of the ice maker, and...

$37.71

Thermostat, Bin

This is a bin thermostat made for standalone ice makers to activate the ice maker shut-off when bin is full. It senses how much ice is in the bin to determine if it should produce more ice or activate shut-off. The bin thermostat may need to be replaced if bin is overfilled, underfilled, or not producing ice. Thermistor can be tested with an ohm meter. This part is made of plastic and metal, and is white in color. This is an authentic part sourced from the original manufacturer.

$6.68

Screw

This screw is sold individually.

$15.59

Switch, Plunger Grid/Light

The purpose of the light switch in your refrigerator is to automatically turn on the light when the door is opened. If the light does not come on automatically when you open the door, the contacts inside the light switch may be burned out, meaning it is time to replace the switch. This package contains both the new light switch and a small plastic spacer. To complete this repair, you will need to remove the control panel section of your refrigerator. The only tools you will require for this repair are a 1/4-inch nut driver and maybe a small flat blade screwdriver. Be sure to disconnect the power source from the refrigerator before completing this repair.

$79.54

Pump, Drain

This part is a drain pump for your ice maker. When you flush the reservoir on your ice maker to remove impurities, the drain pump is the part that removes the water from the reserv...

$50.02

Temperature Sensor

This is a temperature sensor. It may also be known as an ice maker sensor and is used in conjunction with your ice machine. This piece is roughly 3.5 inches long, almost 2.5 inches wide, and includes the necessary wiring connector. You will find this part located in the water pump area of the ice cube maker. The function of this part is to determine the water level within the water reservoir. Once the water level reaches a certain point, the sensor will signal the controls to fill the reservoir.

$33.58

Ice Cutting Grid Wire

There is approximately 10' of wire. Note: 2 kits are needed to replace both directions.

$17.50

Drain Fastener Cap

This is a drain fastener cap and is used in conjunction with your freezer/refrigerator. This model is almost 1.5 inches in diameter, half an inch thick, and is white in color. This piece will fasten to the bottom of the water pan in your ice maker. It keeps the water in the water pan from leaking into your appliance. If your drain cap is loose or broken, the liquid from the water pan will empty and you will have no ice or very thin ice. Make sure when replacing this part to secure the drain cap tightly.

$25.01

Evaporator Thermistor

Used with free-standing ice cube makers.

$32.86

Tube, Plastic

Used with stand alone ice cube makers.

$4.37

Screw

Sold individually.

$156.06

Water Inlet Valve

Includes 5/16" inlet tube.

All Parts for the KUIC15PRTS3
1-14 of 142