KUIA18 KitchenAid Ice Maker - Instructions

Double check the actual part number. While the item looks the same, my unit had a 3 prong plug while the replacement had only 2 and did not fit.

I unplugged the appliance removed the back cover exposing the fan motor.Unplugged the wiring harness from the motor assembly.unbolted the fan motor mounting bracket,and removed. Next I unbolted the fan and motor assembly from the mounting bracket.( I pulled the whole bracket out so it would be easier to reinstall the motor and fan assembl ... Read more y,then reinstalled the bracket with the motor and fan already installed) I installed the bracket assembly with the motor and fan back to its location,plugged the wiring harnessback to the motor. replaced the bask pannel ,and plugged the 110 back in the wall socket

First let me say that the instructional video on your website for this repair was very informative. My son and I watched that before we began the repair. We unplugged the unit first. After removing the back cover, he unplugged the old fan's electrical connection, and then proceeded to remove the fan and bracket from the unit. We then ... Read more removed the old fan from the bracket, installed the new one and then he reinstalled the new fan and bracket back into the unit. He used the included electric adaptor cable to complete the electrical connection, plugged in the refrigerator briefly to confirm all was well (it was), then replaced the back cover and we were done.

my sensor was stuck because of age, so I had to remove the water bucket to pry it out. It is easy to see what you have to remove to get to it. I used the mirror and rachet, extensions, 1/4 socket to remove screws. Tips - Remove the plastic door-inner to help working inside the bin. Also plug the drain because you will drop screws. Ma ... Read more gnet sockets don't work on stainless steel. Later I found it is much easier to work inside the bin by pulling the entire unit out (shut off water and power, remove lower panel and disconnect drain tube). It sounds hard, but actually is easy. REMOVE THE TOP (4 screws). it stays connected because of wiring, but it allows full access and makes all kinds of repairs easy, especially pump replacement and even the circuit board behind the front panel buttons if you ever get to that point.

BTW Partselect is awesome, I have used a number of times for ice maker and dishwasher. My next project is the washing machine! Always the right part shipped very quickly.

My top grid was broken. After removing the old wire and loosening the screws on both ends of the old wire, I carefully unrolled the new wire so there were no kinks. Next, I put one end of the wire in a vice to hold it in place. I put a loop in the other end and attached it to the one end of the frame. You can then hold the grid in both ha ... Read more nds and put tension on the wire as you make the wraps. When you get to the end, attach it to the grid screw and tighten the screw while maintaining tension. You can then cut the remaining wire and reinstall the grid. I think this was much easier than the directions that came with the wire. Took 5 minutes to install the wire on the grid and 15 to 20 minutes to everything back together and start making ice.

Removed the cardboard baking on back. Unplugged the fan. Used 1/4 socket and removed the 3 nuts. Removed the fan. It is tight quarters. Take your time and the job will go fast.

went good

Followed instructions in Sears parts website. Not difficult but tricky to get screws out and back in.

I have a grandson that works for Pantex. He replaced the fan and motor in less than ten minutes using only the nutdriver tool. My cost compared to local supplier and labor was about 75% less.

I completely broke down the unit cleaning or replacing any part with rust. The replacement grid assembly (cutter) came from partselect within days of ordering. I was able reassemble the unit with the new grid assemble. Now have fresh ice. Thanks Partselect... you made this do-it-your-selfer very HAPPY! My wife cannot beleive I got th ... Read more e unit back together.

Just install the new valve by reversing the process of removing the old valve. Only possible nance is with the quick release hose fittings - the collar is pushed down to release the hose. Also, be sure to FULLY reinsert the hose in the new valve. Best to twist the hose a bit when inserting so it goes through the o-ring inside the valv ... Read more e. If not fully inserted, it will leak.

Removed broke wire and replaced new wire. Use gloves to pull the wire tight. That's very important.

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fi ... Read more tting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

Unplugged the unit. Removed 2 screws to remove front cover to access the cutter grid.removed 2 screws to the cutter grid, unsnapped power connector and removed broken grid. Slid new grid in place, reconnected power connector, replaced screws, plugged in ice maker and slid back in place. Very easy!!!

Simple