KUDX KitchenAid Dishwasher - Instructions

i removed the top screw for the water input to the spinner, which gave me enough room to replace the worn nipple pin that the spinner snaps on to. then snapped the new spinner in place. and then screwed everything back into place.

Remove just the 6 Phillips screws holding the control panel assembly to the top of the door. Panel lifted off, clearing the latch assembly. Rested it on my knees as I sat in front on a chair. Control board is right there. Wiring plugs easily pulled off the old board. Their locations are clearly marked on the board by wire colors. Removed ... Read more screws holding old board, replaced with new one, plugged wires onto the new board. Screwed the control panel back on the door, being careful to clear the door latch assembly. Ran the dishwasher through a test cycle (time not included in the repair)and it works like new. Probably saved $150. in labor service charge.

So one day passing the dishwasher while it was running, I noticed a rather pungent burning smell. Yikes, I shut it off!
I took apart the pump housing at the bottom inside the dishwasher, expecting to find some kids toy plastic bit had got caught and had jammed the motor or something. But nothing there, and my dishwasher has a little ... Read more screen to keep just such things from getting to the pump anyway. Hmmm.
So, ran the dishwasher again, seemed ok now.
A week later, same thing, burning smell. Pull it apart again, but no sign of trouble. But I know something is up, so I pull the kickplate and have a look underneath... Way at the back I see a red wire that looks a little melted, but it's hard to tell, so I pull the whole dishwasher out. Sure enough, one of the heater wires is melted and burned, and the plastic locknut holding that side of the heater is badly scorched. Looks like a little electrical fire, I'm lucky it didn't get out of hand!
The heater still tests ok with an ohmeter, but I don't trust it now - order the heater and replacement locknut and washers. Didn't need to order washers, they come with the heater, oh well.
Heater removal and replacement is very straight forward, but I added some high-temp gasket silicone sealant (Ultra Blue) around the seals as I think the original problem may have ben a bit of water leakage causing a short.
Took about an hour to pull the dishwasher out, remove the heater and install the new one, put a new terminal on the heater wire, and put the whole thing back under the counter.
Working great now. But not a problem I expected to have with a 2-year-old dishwasher!

Take the 6 torx screws loose and pull down the face. Pop out the bi-metal fuse that is in the current board. Unhook the wires attached. Pop out the old board. Attach the wires to new board. Put the bi-metal fuse back in the board. Re-attach the face on the dishwasher. Be sure to unplug from the outlet before starting. When finished plug d ... Read more ishwasher back in. This fixed my problem.

Removed the screws holding the metal front of the dishwasher on, removed the 6 screws holding the dispenser in place. Put the new part in and put all screws back in where they were. Put the front back on the dishwasher with its screws, done.

Disassembled inside bottom section of dishwasher found broken chopper part,removed and replaced with new part,only hard part was holding spring compressed when putting in new part,needed needlenose and thin screwdriver.Thank You for your great website and help

remove old seal, clean and dry the gap where the new seal will be installed. Apply adhessive, place new seal, then let dry for 24 hrs.

The hardest part was getting the seal, we first ordered from a sears parts store locally. They also told me that everything was included to install it, but they did not include the adhesive, the ... Read more y lost the order via ups and never notified me. I finally called them and they made me go back to the parts store for a refund. I then ordered on parts select and they had it in my hands in 3 days.

I first thought I may have a defective water feed tube that runs from the bottom of the dishwasher tub aolng the back to the top. This is what the top rack sprayer plugs into to get water.

This was easily replaced by uncliping the feed tube by the two clips, one on the top of the tub and one in the back. You then give the fee ... Read more d tube a twist clockwise about 45 degree (relative to the bottom of the dishwasher). This will remove the feed tube and bottom sprayer.

However, this didn't fix the issue.

I then replaced the pump/motor. This is done by uninstalling the dishwasher and flipping it onto it's back so you can look at the bottom of the dishwasher. There is an electrial connector on the right side that needs to be disconnected. The motor is help on by one bolt in the back and a socket wrench with extender will be needed to get to it. Once the bolt is removed, and motor needs to be twisted about 45 degress so it feels "loose". Then you need to pull straight down and the motor will come off.

Just reverse all the steps to install the new motor.

But that didn't fix the issue either.

Come to find out, the problem I was having was the grinder screen was so gummed up with paper, the grinder broke and water was not getting through the screen. Here is how you replace the grider (which was the true fix to the problem).

- Remove the feed tube like I listed above. You DO NOT need to uninstall your dishwasher.

- Use a Torx driver to remove the three visible bolts on the bottom of the washer tub.

- Pull up on the plastic piece you just removed the screws to remove it.

- Use a smaller sized Torx driver to remove the one screw from the Grinder plate. Once you have the screw off, use a pair of pliers to pull straight up on post sticking straight up on the grinder housing.

-You can now see the grinder. Pull the screen and grinder assembly out. If it is still intact, just clean it and replace it back into its groove. If it is in pieces, it is destroyed and buy a new one.

- Reverse all the steps to put the dish washer back together.

This screen that fits into the groove was jammed up with paper and was causing my my issues. Once I placed this the macine worked great.

Each Molded one-piece plastic upper dishrack wheel mount includes a tiny plastic spring clip which hold the mount in place on the upper dish washer rack.
These clips become dry and britle over time and snap off.
Because they are molded in the wheel mount itself you have to replace the entire wheel mount assembly

Grinding Noise when running. I was not sure of problem and thought that a new Dishwasher may be needed if motor was the problem. After taking the bottom rack and spray arms out I came across my first problem. I believe it was the impeller design that has a 1in hex nut with a bolt in middle that needed to be removed. I needed a 90 degree 1 ... Read more in wrench to hold impleller while I removed Bolt. Luckly I have a friend that is a mechinist who made me a wrench.
After that the grinding cause was discovered - Broken glass that grinded the cermic shaft that is over motor shaft. I did not small drops of water under motor during grinding due to damaged cermic shaft.
$24 and 2 days later my dishwasher is as good as new. Sugguest you sell a 1in 90 degree hard plastic wrench for holding impeller which bolt is removed.
Thanks
PS. - Best part of your site is Parts detail which was very helpful for me to understand assembly.

Removed mushroom shaped float cover by simply pulling up. Cover simply slide down into switch which is mounted through the floor of the tub. Using an adjustable wrench loosened and removed plastic fastening nut allowing removal of switch assembly from below. Disconnected two wires from switch and attached replacement assembly, reinserted ... Read more in mounting hole, reattached nut from top, reinserted float cap and job done! The only tricky part is that the switch needs to be mounted inside assembly, wires connected and snapped shut before reinserting. Not difficult once you figure it out, Also need to make sure rubber washer is inserted on the overflow tube before reinstalling. Keep track as you remove and simply reverse the order. Tried to obtain part locally and was told it would be 6-10 days before delivery. Order from Part select arrived in 2 days.

I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!

This is simple, we don't know exactly how, but when we used the dishwasher the cap must not have been twisted correctly, and after the dishwasher shut down we discovered the cap was on the heating coil and melted. I know that it was easy to fix, but the reason I ordered it from PartsSelect was their price was much lower than Kitchen Aids, ... Read more (the maker), Lowes (where we bought it), and other sites we searched for the part.

Follow diagram that comes with the repair kit

Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls ... Read more out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.