KUDS35 KitchenAid Dishwasher - Instructions

The parts select site had an excellent breakdown of what I needed to replace. When I got the pieces, however, it wasn't so apparent how to do it. I actually used YouTube video to show the process.

The trickiest part was actually uninstalling the broken pieces. I had to work backwards through the YouTube video.

The o ... Read more ther tricky bit is having a sense of how hard you can push to snap plastic pieces in and out.

Also, watch the whole video! I didn't, and I ran out for a tool (a star driver, I think that's what it's called) that was actually in the bag of screws that came with the assembly.

It seems like Kitchen Aid realizes they have a problem with plastic fatigue, because they have replaced some of the plastic parts with metal.

If you take your time and stay organized this is a very doable repair.

First research then troubleshoot
Removed
1 Upper rack
2 Lower rack
3 Lower Wash Arm and Strainer Parts
4 Upper Wash and Rinse Parts
5 Accumulator assy.
6 Motor shield
7 Inlet protector (most difficult)
Noticed blade was broken off chopper assy.
Replaced chopper assy.
Runs and cleans ... Read more like new.
Most difficult step was to remove Inlet protector
After removing two torx screws (#15) used small pry bar to lift inlet protector from position. Not easy to accomplish with hands alone. Inlet protector fits tightly into position.

Dish rack adjuster kit W10712394: I am a fully inexperienced and non-mechanical mom who needed her dishwasher during this holiday season! It took me a little longer and seemed a little harder than the description said it would - but not by much. The dishwasher is now better than it was when we bought it. Tip 1 - The original mechanism had ... Read more no screws. The replacement kit does. The kit comes with a special screw that you will need in order to use a phillips screwdriver. It would have been helpful to know that before I tried to screw the screws in and stripped the first one because none of my screwdrivers fit. 2- Instructions aren't clear and photos are a little distorted (2D rather than 3D) for a novice. I wish I'd known this request for installation instructions was coming before I finished the project so I could have taken pictures. Tip - Take pictures to submit for installation instructions for others to appreciate. Would be nice to have some kind of perk to motivate people to do the work of clarifying instructions and submitting pictures. 3 - The part that locks the sliding mechanism into place is a little tricky. That step in the instructions needs some attention. I don't know how to clarify it further but other than the problem with the screws, this is the part that consumed time that an experienced dishwasher repair person might have breezed through.

Watched the u tube video. Very clear! He said up front what kind of screwdriver to use and it was necessary to have that kind and size of screwdriver.

I followed the instructions on your recommended video; so easy! Thank you!

Pulled off old seal. Pressed into groove the new door seal. No parts required.

Removed old gasket, cleaned track thoroughly, then followed instructions from video on Part Select order form. Instructions very clear and precise. Getting the new gasket was a little tedious at the corners but take your time and work the gasket with your fingers as shown on the video.

I looked up the repair on youtube and followed along step by step.
I am a 64 year old female and the job was easier to do while watching a repairman than it would have been to read instructions.
The internet is great for some things!

Disconnected power to dishwasher. Removed water supply hose from inlet water valve.
Removed lower and upper racks. Removed Lower spray arm. Removed tube from pump tp top spinner. Pulled dishwasher from under cabinet (remember to tip to get back out!). Placed dishwasher on its back. Removed electrical connectors from water valve, main ... Read more motor and drain motor. Removed drain hose from drain pump. Removed pump/motor assy by pulling out wedges and pushing assembly into dishwasher. Removed pump/motor assy from inside dishwasher. Cleaned out pump. Installed new chopper. Re-install pump/motor assy. Re-install driain pump hose. Re-connect the pumps and water valve electric connectors. Slide dishwasher near cabinet for re-install. Re-connect drain hose to dishwasher. Re-install dishwasher under cabinet.Reconnect water supply. Removed top spinner from tube. Installed new spinner onto tube. Re-install tube onto main pump (below lower spray arm). Clean out and re-install lower spray arm. Remove middle spray arm from top rack. Clean out spray arm. Re-install spray arm with a new gasket (gasket may have not been needed). Re-installed lower and top racks. Re-connect power supply. Position all three spray arms pointing towards the door to confirm they were turning. Tested dishwasher - confirmed fill, wash, and drain properly. Also confirmed that all three spray arms were turning. Machine is washing, draining and running great since!

1) clear out the dishwasher
2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top
3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection
4) close the door! pull back the insulation from the area of the hin ... Read more ge and photograph both sides - this will save you the pain of going online
5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides
6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point
7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them
8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame
9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly
10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame
11) you've done it!
12) have a cuppa and do your second washer that hasn't failed yet - it will soon.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

Watched the video and it was perfect. Very easy.

Watched the video. Easy!!!

The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.

I am a 61 year old woman and it took me a total of 2 min. max. Popped it into place and pushed in button that holds it..Taa Daa...perfect!