KUDS03F KitchenAid - Instructions

Unplugged unit from power source.Removed the screws fastening the interior panel to the door. Removed latch assembly from the door after disconnecting two wires to the microswitch. Removed microswitch from the latch assembly, then installed same microswitch in new latch assembly. Re-connected wires and re-installed latch assembly. Re-inst ... Read more alled interior panel with screws. Re-connected unit to power source. Tested unit. Has started reliably ever since.

Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump ... Read more . Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com

Soap dispenser unit could have been repaired by pushing the plastic arm back home and adding two drops of instant glue to keep the plastic shaft in proper place. Didn't need to purchage a new unit.

The upper spinner was laying in the top washer basket. I went online but no help was avaiable. Went to store where we purchased dishwasher and they gave me part number to order but not online I had to call to order. Part arrived in about three days. I took two screws loose on the top of dishwasher removed broke retainer to put new retai ... Read more ner in but I drop it into dishwasher so you have to me very careful
so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.

too simple to describe

took out the old one and plopped in the new one

Just snapped the new retainer onto the side tines. It holds the rear tines upright on the bottom dishrac.

Remove front door panel, replace B-metal fuse.

Needed to replace whole soap dispenser unit. Had to take front door apart cause the hex screws are on the inside. (10 Screws) then doors falls off onto floor if not careful. Spring loaded inner door wants to go up and outside door wants to fall off pulling on wiring. Unplug wiring to solinoid,(plug has locking release lever that needs ... Read more to be pulled on) remove 6 hex screws, and dispenser comes out. Install new unit with 6 screws, plug in, and get help holding door parts together while installing the 10 screws. You are now finished. Pros are you get the complete unit, and not a bunch of parts. Cons are no diagrams or instructions/no new 6 hex head screws-reuse old ones. . . . . . Do not use soap powder/causes damage to latch parts/use only liquid soaps. . .

First, ordering parts and getting diagrams from parts select is so efficient and make tthe installation so manageable. Using installation tips off the site gives u confidence to do it.
My issue was that I could not get the dishwasher from under the counter.
I removed the kick plate and screws holding it to the counter, but it w ... Read more as not coming out all the way. So I had to use a coat hanger to hook the spring. I attached the nylon cord first. Then I pulled the spring taut with the hanger and it was easy to thread the cord around the pulley system. I actually attached it to the door before tensioning the spring to make it easier.
Door works great now.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Just snapped it right into place! No tools required. Very easy!

Replace motor/pump assembly

Just replaced the original cap with the new one. It fit perfectly. Thanks.
P.S. - I would rate this excellent. I would give it 5-stars.

I peeled off the old seal and replaced with the new seal. The instructions were clear and easy to follow, however the new seal made the door not stay closed as the friction catch at the top was no strong enough to overcome the tension of the door closed with the new seal.

There were explicit instructions on the way the seal ... Read more was to work with the sealed edge spreading into the tub area as the door closed. I was very careful to follow those instructions and made sure to seat the seal carefully. After I reinstalled the seal three times to see if I could get it to seat properly, as a last ditch effort I reversed the seal to the opposite way the instructions indicated and it worked with the door closing properly and the seal didn't leak.

Based on looking at the old seal and how it was originally installed, I actually think the seal was out of spec for the unit. However, if it isn't leaking that is what it's all about so we will see how long it holds.