KUDP01ILBT7 KitchenAid Dishwasher - Instructions

Removed leads from fuse and installed jumper wire (while the power was off, then turned back on) to determine that circuit board was still good. Ordered new fuse and installed using existing wire connections. Did not splice in new connectors that came with fuse. Wires were clean and good and did not want to cut and splice.

Since I had watched a repairman diagnose the problem, it was eash to reproduce how to pull the unit out from the wall and find the faulty part to remove it and replace it with the new thermistor. Two wires to disconnect and connect and repair nearly complete. Pushed it back in, screwed it back to the cabinet and installed foot plate and ... Read more done.

I order a pair of wheel mounts and replaced both. Squeezed ends of plastic "plug" on the front edge of each rail (top shelf) and removed plug. slid out top shelf, snapped off old whell mounts, snapped on new wheel mounts, slide shelf back into track and re-inderted end "plugs". Done!

Just snapped the new retainer onto the side tines. It holds the rear tines upright on the bottom dishrac.

took out the old one and plopped in the new one

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I had removed this part several times before, it had clogged from sediment, so I had practice. That issue was resolved, but I determined the water level during the wash and rinse cycles was low, and the valve appeared to be the culprit. The trick is to remove the valve from the bracket, removing the single screw, and sliding the unit s ... Read more o the tangs on the bracket can be pushed to the rear and then towards the front. When you disconnect the electrical connection, then the valve can be pulled out towards the front for better access and to disconnect, if your supply hose is long enough. That makes swinging the wrench easier. Other wise it is tedious. Make sure to reapply thread tape after reconnecting the supply hose.

Replace motor/pump assembly

Be sure to shut the power off before you attempt this first step, there are electrical connections all around this area. At first I didn't realize to get at the door handle I only to remove the top four screws on the inside of the door. After figuring this out the job was fairly easy. Once inside the top part of the door, all I had to do ... Read more was snap off the old handle and snap in the new one. Test it to see if it works before you shut the door.

I peeled off the old seal and replaced with the new seal. The instructions were clear and easy to follow, however the new seal made the door not stay closed as the friction catch at the top was no strong enough to overcome the tension of the door closed with the new seal.

There were explicit instructions on the way the seal ... Read more was to work with the sealed edge spreading into the tub area as the door closed. I was very careful to follow those instructions and made sure to seat the seal carefully. After I reinstalled the seal three times to see if I could get it to seat properly, as a last ditch effort I reversed the seal to the opposite way the instructions indicated and it worked with the door closing properly and the seal didn't leak.

Based on looking at the old seal and how it was originally installed, I actually think the seal was out of spec for the unit. However, if it isn't leaking that is what it's all about so we will see how long it holds.

Although the lower rack was a slightly different style than our original, it fit the dishwasher perfectly. We needed to transfer the silverware racks to the new rack and insert one set of removable tines. About 5 minutes and we are very happy with the repair.

Pulled everything out the front, and dug down to find a thrashed chopper assembly (like a little garbage disposal). The previous owner just tossed anything in; pop tops, plastic cutlery, etc.
Didn't pay attention to the exact installation of the chopper as I pulled it out, but, it turns out that it only goes in one way.
Used pi ... Read more ctures and instructions I found online as a guide and didn't have any issues.
Replaced the check valve because it isn't expensive and I was in the neighborhood.

Just had to transfer all the kit parts from the old rack to the new one.
It was important to leave one side of the kit parts(the wheel and other plastic pieces) on the old one while transferring the other side of the kit parts to the new rack so that I had a visual reference for placement and orientation of the parts on the new rack.

I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher ... Read more has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.

Remove upper tray and spray arm. Remove two screws retaining pipe for upper spray arm and overhead. Unscrew retainer on top of lower spray arm and remove. Gently rotate the upper feed pipe clockwise until pipe can be removed from lower pipe. You may then remove the lower pipe and bearing housing where the seal is. Reverse order for reasse ... Read more mbly. I also replaced upper spray arm bushing. Very simple, remove one screw and the arm will come out.