KUDM24SEWH3 KitchenAid Dishwasher - Instructions

replaced spray arm, but this did not resolve the problem. The troubleshooting guid (inside kick panel) indicated the check valve may be stuck. We had quite a bit of lime build up, so I suspected the loose deposits may be stuck. I removed all of the deposits, disassembled the lower unit.
Removed lower spray arm, removed spry tube. ... Read more The tube is two pieces. first the upper portion must be removed (two screws-place towel on base of tub to preven screws from falling into the chopper area), and then the lower portion simply rotates clockwise 1/8 of a turn. The attachment for lower spray arm has a small plastic bearing, careful not to drop it.
The dishwaser then had to be pulled out and turned on the side. I removed the entire lower unit by removing the white tabs (3). Careful, because the unit is now free to drop into the tub. Next I removed the pump. This is tricky as you have to remove the aluminimum bracket to get to the mountin bolt. The bolt turns out easily w/socket and extension. The pump motor is then rotated counter clockwise, and pulled from the pump. Takes a little force as the gasket makes for a tight fit.
I then removed the choper / pump unit from the basin. The build up behind the chopper screen was extensive, so I had to remove the screen and then the chopper cover. After cleaning, the check valve was unplugged and I reassembled the unit.

Dishwasher works great now.

I simply unscrewed the remainder of the wash arm retainer nut, removed the wash arm bearing ring and spray arm bearing ring and replaced them; No tools were required. At the same time I decided to replaced the upper wash arm with a kit from Part Select. This did require the use of a philips head screwdriver. The job was real easy and ... Read more accomplished within 1 hour.

just pay attention to how the old gasket was installed, then pay close attention to how you remove it from its groove. replace with flat sides and grooves just the same.. I actually left about on third of the old gasket in place until I seated the new gasket to make sure I was doing it correctly. visually divide the gasket gr ... Read more oove into 2 parts with the dividing line at the top of the groove, place a piece of tape on the new gasket at its middle and begin there, first one side then the other,,, that way there is no stretching to complete the circuit. easy , I am a 62 year old grandmother of 7,,,,,,,,,,,,,,,,,,,,,,,,,,,

Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.

Simply followed the instructions that were provided with the part.
Locking the inside vented piece to the outside assembly was difficult because it is located deep along the side of the dishwater (leverage) and I was not sure how much pressure to apply to the part for fear of breaking it. But it did snap into place after several att ... Read more empts.

I looked up the part on the Internet and checked locally. The part had to be ordered locallybso I placed my order on line. The part came quickly and the instructions were fairly clear. The parts just clipped together which made it vey easy to so and it is nicer than the rack we had before.

At first I considered replacing the gasket on my own but was not sure If that was the problem. I had a service person come in (at great expense) to tell me it may or may not be the problem but he could order the gasket and replace it. I did it myself.

I removed the old gasket by hand, simply by pulling it out of its track. I s ... Read more prayed clean water in the track to clean out old soap and debris. I soaked the new part in warm water for a few minutes to soften and lubricate it. I centered the gasket in position and began pushing it into the track with a one inch putty knife, being careful not to damage the rubber. There is a slot along the gasket that will accept a flat tool to push it in. At the corners, I had to use a screwdriver to work around the curves. In a few minutes the gasket was in and no more leaks. It couldn't be easier.

Removed the old mount from the upper rack. Removed the broken stem from the old mount that was attached to the arm. Attached the new mount to the spray arm. Attached the mount and arm to the rack.

Hey parts select, I'm Julia's husband and the repair was a simple remove and replace. Only one screw to hold the manifold together and the mounting hardware that we had to order separately was a snap in piece which was different form the original but went in just fine. You saved me from having to buy a new dishwasher which Julia was more ... Read more than happy to go shopping for!! Thanks!!

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

I had replaced the control board a month or two earlier. Then smelled plastic burning. I noticed the Sta-con connecters in the molex plug had burned - that's what took out the control board. The fuse assembly came with new connectors - so you know this is a known problem with the machine. If you're handy you can buy the thermal fuse f ... Read more rom Newark for $0.88 and replace it by soldering - but you need to replace the sta-cons. They corrode and the bad connection causes the heat making the thermal trip.

Removed 2 screws that held the old mount and washer arm in place, new mount was very easy to install, it snapped in, only one screw needed, remounted the washer arm and the job was done. I was really impressed with the ease of ordering and how quick it got here (3 days), also the scematics you have online are very helpful. I printed them ... Read more out since I don't have the owners manual any longer, they're very helpful in matching up and ordering the right part which saves a lot of time, also I like the way you can just search by model number and appliance name to find the right parts, makes the entire process really easy. I know I will continue to shop here when the need arises. It really cuts down on expensive repair costs.

Once the covers under the door are removed, the check valve is visible (unless its too dark, hence the headlight), and pointing right at you. Since I was working under the dishwasher, I gathered all the tools I thought I might need and laid them on the floor next to. Removed 2 covers, placed pan under check valve and hose to catch any wa ... Read more ter, squeezed clamp with (wrong) pliers, it eventually came loose. Carefully twisted hose off check valve. Water came out, some of it got into the pan, most of it on the floor. I guess I should have pumped it out before I started this. Plastic check valve is screwed into the big piece of whatever, carefully grabbed it with (wrong again) pliers and turned it out. Installation is reverse of removal - but use a large pliers with a ROUNDED jaw to grab the round check valve body. Don't squeeze too hard or overtighten it. Put the clamp on the valve before pushing the hose on. Be sure the hose seats all the way onto the little lugs. Compress the clamp, slide it over the end of the hose and release. That's all folks, works good now.

Actually I ordered the drain and wash impeller kit because it was listed as the #1 cause of failure to drain. I then hired a plumber to install it. He did so and that didn't solve the problem. So I was about to buy a new dishwasher. I then noticed that the second most frequent cause was a problem with the "dishwasher drain check valve." I ... Read more watched the "partselect" video on how to change that. I didn't have a new one but I thought I would take out the part and see what I could learn. As it turned out it was blocked by a little piece of what appeared to be a walnut chip. I cleaned it out reinstalled the drain check valve and the problem was solved.

Removed the inner door panel and then the circuit board protective cover (which just snaps in). Fuse assembly is readily accessible and just snaps in. The wires are attached with spade lugs using existing wiring. No wiring modificatins needed,