KUDL0 KitchenAid Dishwasher - Instructions

Each Molded one-piece plastic upper dishrack wheel mount includes a tiny plastic spring clip which hold the mount in place on the upper dish washer rack.
These clips become dry and britle over time and snap off.
Because they are molded in the wheel mount itself you have to replace the entire wheel mount assembly

The air inlet strip has a flap and two smaller side flaps that seal the bottom of the inner door to the bottom pan that hold the water. The flaps don't form a watertight seal as they only serve to prevent the water surging during wash and rinse cycles from splashing out of the bottom pan onto the floor under the door. What I learned aft ... Read more er dismantling the door is that the problem I was having with water dripping from the bottom of the bottom of the outer door was being caused by a loose upper round louvered vent and not he lower vent strip. If the lower vent strip were the problem, water would leak from the front lip of the bottom pan, which is located well behind the face of the front door panel.

Here's my recommendation on the lower vent srtip repair. Turn off the power to the unit at you breaker panel. The air inlet strip is fastened to the backside of the inner stainleess steel door panel. To access the screws the outer door panel must be removed. Open the door and remove the six torx head screws that fasten the outer door panel to the stainless steel inner door. Don't remove the two torx screws top dead center as they hold the door latch. After removing the screws, raise the door up to the nearly closed position. Lift up the outer door panel handle and door bottom to disengage the outer panel from the inner stainless door. The next part is a little tricky since the vent strip hex head screws are at he bottom of the stainless door panel, facing out with the door closed. The lip of the bottom stainless pan is high enough to make it a tight fit to access the screws. There is also a steel bracket that is a door stiffener and holds electrical wiring. I found removing the bracket held by a 1/4" hex head screw on each side made access to the vent strip scews easier. Lay flat on the floor. With a 3/16" nutdriver or socket wrench each of the five vent strip screws can be removed. It's a tight fit between the bottom lip and door bottom, but it can be done. Remove the old vent strip and attach the new one. Make sure it fits snugly into the slot. Best to have an extra pair of hands at this point to hold the stip securely in place while screws are reinserted from the opposite side. Reassemble everything in reverse order.

It was when I had the outer door panel off that I noticed my problem was water getting past the upper round louver vent seal and thus running down the inside of the outer panel. Simple fix was to remove and clean the scale residue from the parts and door. Then reassemble the vent and twitst tighten the vent to compress the rubber seal on the inside face of the door.

SAFTY: Turn water off. Flip the circuit breaker.
PREPARE FOR REMOVAL: Unscrew / Remove kickplate. Disconnected water connect just behind the kickplate. Be ready with a couple of dishtowels. Pull the door down and remove any screws that go into the under part of your counter top. Jack the front legs screw down.
REMOVE: Gently p ... Read more ull the Dishwasher from under counter. Push the insulation flat against the side of the dishwasher about every six inches that you pull the dishwasher out to prevent it from snaggin on the cabinet face edges. Remove the baskets and spray arms. Careful not to damage the heating element.
NOTE: Here I noticed that the guy who installed the dishwasher kinked the copper line limiting the water into to my dishwasher. So my circulation pump/motor was probably running dry. I replaced with a flex type "dishwasher" hose that will easily coil up behind / underneath without kinking when I push back in. DO THE REPAIR RIGHT - DO IT YOURSELF!
REPAIR: I gently laid the dishwasher on it's side (cardboard underneath). I disconnected the power - 2 wires. Then, I only disconnect one wire harness, the sump tubing and the I thought I'd better remove the impeller that the sump tubing was connected to (it was only attached with one screw). Remove the 3 plastic clips around the pump/motor. Carefully push the pump into the dishwasher. DO NOT LET THE PUMP FALL AS IT MAY DAMAGE THE HEATING ELEMENT IN THE DISHWASHER! Push the new pump/motor in place until the seal is at least flush with the bottom. I used the back of a wood spoon. Don't pull on any part of the motor from the bottom or you'll break the thin aluminum casting. Just inserting the plastic clips back in place will pull the seal flush with the bottom again.

I was lucky. I simply removed the motor/pump, replaced it with the new motor/pump, and put everything back together in reverse. I put a little bit of silicone grease on the o-ring of the temperature probe. I happened to have some silicone grease because I also have a pool.
Done. It cost me $220 Vs. $550 quoted by Sears. That doesn't count the extra Sears would have charged my for repairing the kinked copper line. And you know they would've kinked it again. That only cost me $20 more and the flexible line couldn't have been easier to install. I could have done the whole thing for less but I opted to replace the pump/ motor together.
Getting it all done right, no leaks, no kinked line, keeping the dishwasher that matches the other appliances (VS. replacing it at $550 repair price), all less than 1/2 the price of a quoted repair - PRICELESS. - THANK YOU PART SELECT. DISCLAIMER: I have no affiliation with Part Select.

Removed mushroom shaped float cover by simply pulling up. Cover simply slide down into switch which is mounted through the floor of the tub. Using an adjustable wrench loosened and removed plastic fastening nut allowing removal of switch assembly from below. Disconnected two wires from switch and attached replacement assembly, reinserted ... Read more in mounting hole, reattached nut from top, reinserted float cap and job done! The only tricky part is that the switch needs to be mounted inside assembly, wires connected and snapped shut before reinserting. Not difficult once you figure it out, Also need to make sure rubber washer is inserted on the overflow tube before reinstalling. Keep track as you remove and simply reverse the order. Tried to obtain part locally and was told it would be 6-10 days before delivery. Order from Part select arrived in 2 days.

I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!

First I checked the power supply and noticed the breaker was not tripped. Confirmed the unit was getting power. I then downloaded a parts breakdown from the Kitchen Aid website and noticed there was a fuse mounted in the control section. Using my digital multimeter I confirmed there was no continuity through the fuse. I then ordered the p ... Read more art, installed it and washed a load of dishes:-)

This is simple, we don't know exactly how, but when we used the dishwasher the cap must not have been twisted correctly, and after the dishwasher shut down we discovered the cap was on the heating coil and melted. I know that it was easy to fix, but the reason I ordered it from PartsSelect was their price was much lower than Kitchen Aids, ... Read more (the maker), Lowes (where we bought it), and other sites we searched for the part.

Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls ... Read more out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.

I initially thought the pump assembly was dying (or was damaged by a piece of glass or something that had gotten into the pump. I priced the parts and decided I wasn't sure the unit was worth it. But the dishwasher was also not cleaning well, and was leave soap on the dishes. Turned out the water inlet valve was intermittently failing ... Read more to open. Using the troubleshooting guide (both downloadable and inside the bottom panel) was no help. I just checked and saw that there was power going to the valve when it did not open: diagnosis made. Step 1: turn off water to dishwasher. Step two: remove bottom panel. Step 3, place towels under dishwasher. Step 4, disconnect water line from elbow screwed into inlet valve. Step 5: remove inlet valve screw with nut driver and slide valve sideways and back to remove. Step 6: slide clamp on hose to dishwasher away from valve using pliers. Some work involve with sliding hose off the valve (careful, the hose is accordioned plastic) Step 7: remove elbow from inlet valve (this required a visegrip to hold the narrow nut surface on the valve and a wrench to turn the elbow). Step 8: apply Teflon tape to elbow and screw into new inlet valve. Step 9: install hose to dishwasher and return clamp to hold hose in place. Step 10: reinstall valve by placing tongues into grooves and sliding to the left, reinstall screw. Step 11: tighten elbow with wrench, now that valve is held in place. Step 12: reinstall water line. Step 13: turn on supply line and check for leaks

the parts only took a few days to arrive, and it took me about 2 minutes to install them-no tools were required. i took out the end plugs from the slider bars, slipped out the old broken wheel parts, snapped on the new ones, slid the upper rack into the slider assembly, popped the end plugs back into place and VOILA!!

aside fr ... Read more om the expense of the parts- much better to go this route rather than hire a repair guy to do it!!

Recoved the screws which secured the handle assembly (approx 8). Removed the old parts and screwed home the new parts and replaced the assembly. Worked perfectly.

The hardest thing for me was to decipher the model number as they use '1s' and 'Is' and you can't tell them apart.

Also the part diagrams should have each ... Read more part number listed to make it easier. Took me longer to work out what to order than do the repair.

Mine was an easy fix, lift out old and insert new. I just want to comment on the excellent service I received. I ordered on one day and my product arrived the next! Amazing! Thank you,PartSelect!

After replacing the thermal fuse 5 times i noticed the new packaging came with a terminal block on then fuse harness. PLEASE USE THIS. It is a must, it supposedly is acting as some type of heat sink or something for added protection. Used the unit on all cycles now and works great. Just follow fuse instructions precisely. Hope it helps.

Before starting the repair, I turned off electrical power to the dishwasher at the circuit breaker.

Instructions for removing the door cover panel were included in my dishwasher installation manual. The instructions were in a section for adding a custom door panel. For my dishwasher, this only required removing six screws usi ... Read more ng a Torx (star shaped) driver, size T15. I found it possible to support the door cover by myself with a knee under one side and one hand wrapped around the opposite side, but another person would be helpful.

The electrical connector to the dispenser has a small tab to lock it in place. I gently pried the tab back a *little* and pulled out the connector.

There are six screws holding the dispenser in place. In this case, they were 5mm hex head screws. The screws hold a metal bracket in place and a vinyl flap is sandwiched between the bracket and the inner door panel. The vinyl flap has three holes, with two of the screws passing through the left and right holes, and the middle hold goes over a plastic tab on the dispenser.

After removing the bracket and vinyl flap, I found that there were two metal tabs holding the dispenser in place. These tabs are part of the door sheet metal. Gently prying them back a *little* released the dispenser (which would have fallen out if I hadn’t kept a hand on it).

I pushed the new dispenser through the opening until it clicked into place with the metal door tabs holding it. Then I put the vinyl flap in place with the middle hole over the plastic tab on top of the dispenser, and put the metal bracket over that and attached with the hex head screws.

Next, I reconnected the electrical wire to the dispenser, installed the door cover panel, turned on power at the circuit breaker, and tried a wash cycle. The new dispenser works great!

Didn't have to remove any screws, etc. Just had to pull the old gasket out of a grove in the top and sides of the frame, clean up the particles caused by the deterioration of the old gasket, and install the new gasket. Have to be careful to start at the top center of the frame exactly in the midpoint of the gasket and carefully push the g ... Read more asket into the grove with your hands. Try not to stretch the gasket. There will be about 2 inches of extra gasket laying on the bottom on each side of the dishwasher, and that is OK.