KUDC24 KitchenAid Dishwasher - Instructions

I removed inner face of door, cut wires leading to door switches, and then installed the new door switches and wire harness.

I removed the rubber boot on the top of the water dispersal unit ( stainless steel wand ) by turning it counterclockwise and the wand came off with ease. I then removed the top unit under it by removing the 8 torx screws and removed it. Under the unit is a cover with 1 torx screw to be removed and removed the cover to access the unit. I w ... Read more as unable to loosen the 1/4" nut on the shaft as it was very tight so I had to remove the unit and lock the motor armature with a piece of wood and removed the bolt. Using the kit I purchased I installed the new parts as required and it works as good as new.

The whole problem started with the upper vent on the door being plugged up with a whole bunch of labels that had been washed off of a bunch of tin cans that were washed prior to recycling them. Te high water float was also gummed up for the same reason and overflowed on the floor, I pulled it up and out and cleaned it up also, it works as good as new.

Removed dishwasher lower faceplate.
Removed hose clamp at the dishwasher end.
Removed clamp at the garbage-disposal end.
Removed hose.
Pulled new hose.
Connected both ends of the hose.
Installed both clamps.
Tested.

Put wheels on new bottom rack and put back in dishwasher. Like that the back racks can lie down for pots and large dishes. Removed the the wash arm and replaced the ring. Too easy

My wife noted wood floor bucking up around dishwasher - pulled dishwasher out from counter, tipped it on it's side, looked underneath, & noted slight corrosion on top of motor -

Took motor/pump assembly completely off of dishwasher (comes out from the bottom) by flipping four little plastic cams on motor to the side & then to ... Read more ok pump apart (starting at top & working down) till I got to the impeller/motor shaft seal.

Found plastic impeller worn through into two pieces & little spring thingy under the grinder-upper thingy broken.

Ordered Drain & Wash Impeller kit - got it a few days later - installed (new motor shaft seal didn't seem to be quite the same as far as fit, so I didn't use it - just used the impeller & new spring thingy)

Put it all back together & runs fine - no more leaks - (now just have to figure out what to do about warped wood flooring - oh well, it's old & is probably time for whole new kitchen floor anyway)

Note: This particular Kenmore model made by Whirlpool - takes Whirlpool parts.

Note 2: Needed only screwdrivers to do this whole thing - would have been a really quick/easy repair if I had known what the problem was & how it all comes apart. took a little time to figure it out. (I am a rank amateur at dishwasher repair)

Removed the 4 screws that hold on the 2 lower front covers. Removed the old broken spring with just my fingers. Put the new spring in, again, with just my fingers. Put the two covers back on. I didn't even need to slide the unit out from under the counter!

Replaced both "tracks" and the "wheels" .
Now it's like new....!!
My wife is so happy

Removed the track end caps from the tracks so I could pull out the tracks.
Removed the upper wash rack that holds dishes.
Only by removing this rack can the wheels be replaced, if I tried to replace them with the rack at ... Read more tached to the dishwasher I had to bend forward painfully.
Replace the old rales with new ones.
Attach new wheels to the upper rack in such a way as to allow the rack to roll inside the new rales.
Replace the end caps.
Hope it lasts another 10 years

After doing some research in a repair book I decided to take a stab with a water inlet valve. With expedited shipping I ordered the part and within three days it was delivered. I installed it and the dishwasher seemed like it was trying to fill but still would not. After much cocnsternation I turned the water supply valve to the dishwash ... Read more er a partial turn to close and I felt the water rush through the valve and the dishwasher then filled. Apparently the shut off valve must have been clogged plus it now leaked. I then replaced the shutoff valve and the copper pipe to the water inlet valve with flexible 3/8" tubing and the dishwasher thus far is running fine without leaks.

The mounting bracket was broken.

The parts ordered were a direct match due to the fantastic pictures supplied on this site.
A dealer wanted to order it and then I would have had to drive and pick it up - no way.

partselect.com first time user - very easy.

Directions were somewhat generic, but clear enough to figure out that I had to remove the toe plate and front cover below the main door to disconnect the two springs that held the door in tension. I then removed the old door seal (really a splash guard), and scraped off some scum. Then I pried apart a metal tab on each side of the door t ... Read more o facilitate lifting up on the two hinge rods on the door to get to the two corner water diverter pieces that really keep the water in the dishwasher. These two pieces deteriorate over time like the splash guard. The reverse assembly process was simple, NO LEAKS.

I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassem ... Read more bled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!

Just followed the instructions and used the old one as template to snap components together. Quality seems to be same as the original one and Part Select was some 15% plus less expensive then next best competitor

The only difficult part was taking out (relatively easy) and returning (hard) the clips from the rails. This required bending the end of the metal rails with pliers. Otherwise the dishrack just rolled in with no issues.

The spinner is somewhat lower than the one it is replacing, making the clearance over items in the lower rack ... Read more to be serviceable but marginal.

Water was not being sprayed thru the arms. I opened the dishwasher, removed/unscrewed the spray arms and wash impeller (black plastic wheel that directs the water) and then noticed that the part below the wash impeller had broken into pieces. There was only a metal ring and it was supposed to have a spring attached to it. I replaced the r ... Read more ing/spring below the wash impeller using the part from the Drain and Wash impeller kit. The dishwasher works great now.

It was my first mechanical fix. Use the web to diagnose, find the specs of the appliance and use common sense and you can do it yourself too.

By the way, the parts from this site arrived the next day.

Turned off the power, just to be safe.

Removed the lower panel (4 screws). That made it easier to remove the lower 2 screws on the door panel. Slid the panel down slightly, then pulled off.

Removed the old dispenser - disconnected 2 wires, removed 6 screws, pushed in the plastic clips.

Pushed the new unit ... Read more into place - clips click in. replaced 6 screws and 2 wires. Put the panels back on. Power on.

About 25 minutes.