KUDC03 KitchenAid Dishwasher - Instructions

To replace the soap dispenser you need to take off the front of the door, which requires removing about 12 torx screws - of 2 different lenghths (so keep track). Then the soap dispenser is held in place with 6 very small 4mm hex screws (why they used these instead of normal phillips??). Both my hex sets stopped at 5mm, so I had to go g ... Read more et one. Tool has to be narrow (not one that is flared) because the clearance between the screws and the unit is very tight. There is one small two-wire connector with a press-in connector that at first looked hard to pry off, but just grab it with channel-lock and it will just come off. Remember which way the wires are facing (ie. up or down). Be sure to note how the vinyl flap (that covers the back of the dispenser) attaches, then pull out the old one. Once the new one is in, the hardest part is putting the door cover back on. I'd advise having an extra set of hands. Made it much easier.

Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.

Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.

Delivered in 1 day. Fantastic. Highly recommend

open door remove 8 allen screws

change circuit board 6 wire plugs

Primarily, I read the instructions on line and watched the great videos explaining the repair. While the DW was out, I decided to change out the Drain Pump and the Chopper Assembly, even though only the Circulation Pump and Motor was my problem. These three items are the primary mechanical wear components and it made sense to me to repl ... Read more ace these items. Perhaps I'll get another 10 years out of the DW. Two notes about the repairs. If you replace the chopper it isn't clear in the video where exactly it fits into the housing as the video mechanic did a great job of blocking the view of this part of the procedure. It took me awhile to figure out the chopper screen didn't go in the narrow trough, but just outside of that trough. Also, to lubricate the gaskets when putting the motor and the drain pump back in, I use a light coating of petroleum jelly. It is a good lubricant to facilitate the insertion of the both pumps. The pumps slid in easily and there were no leaks when I test ran the DW outside of the cabinetry. If you have a modicum of mechanical ability this job is a very simple, straight forward process. Good Luck!

First I unplugged the dishwasher.Then I removed 6 Torx screws, popped off cover, cut wires to old fuse, stripped wire, placed wires in new part, tightened screws, reassembled in reverse order, plugged unit back in and tested. WOO HOO!

I saved over $150.00 by doing it myself instead of having a repairman come out! That's 4 free ... Read more fishing trips!

1. Removed six screws securing outer panel to dishwasher door.
2. Removed outer panel which exposed back of dispenser.
3. Remover six screws holding dispenser.
4. Removed dispenser.
5. Installed new dispenser.
6. Replaced six screws.
7. Reattached electrical connection to dispenser relay.
8. Reinstalled ... Read more outer panel with six screws.

Lifted out old basket, discarded, and set new basket in place. :-) Rocket science? NOT.

Started as dishes not getting clean and I observed that the top arm was not spinning and there was very low water pressure coming out of the jets. After making sure the water level was up to the bottom of the heating element and making sure the jets were not clogged I checked the filter and chopper. It was a little tough to get the cover ... Read more off of the chopper but once I did I could see that the chopper scraper was broken off and the shaft was broken. The screen was all clogged up with stuff. Ordered a new assembly and put it in making sure to compress the spring and make sure the gears lined up. Now it is running great.
I think the Kitchenaid is the same as the Whirlpools.

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

Turned off water and disconnected line, then disconnected drain, turned off power and slid dishwasher out and turned turned upside down and removed hold down bolt ( it is a 3/8 head bolt) removed wire from motor and twisted motor assembly approximately 1/4 turn counter clock wise and removed old motor and seal assembly reinstalled new mot ... Read more or with new seal and rewired. Turned washer back upright and removed filter assembly and lower jet arm, removed cover for food disposal and reinstalled disposal blade back on pump drive reinstalled cover and filter assembly and jet arm. Slid unit back in place and anchored down to cabinet and turned water and power back on ran washer through a short cycle to clean any soap build up that was left inside and that was it, it all works just like new.

After I took apart the inside of the door, removing 12 star screws, I was able to see the inside of the automatic soap dispenser device. Since I now had the new device to look at, I was able to replace the latch pin back in the existing device and it worked!

I now have a replacement if the device actually breaks in the future ... Read more and looking at the small plastic pieces, it will probably happen sooner or later.

Removed the Bi-Metal fuse and ordered a new one and recerved it two days after ordering. Replaced it and it worked.

I cleaned the chopper and screen a few times and it continued to get blocked after a couple of cycles. Replaced the chopper assembly and now it works find.

I ordered this part after the sanitized light on my dishwasher was flashing. The dishes were no longer drying. To replace the part, my husband pulled out the dishwasher and unscrewed some nuts (accessing under the heater through the side openings). The entire repair took under 15 minutes, and works perfectly. I have to mention that th ... Read more e heater was shaped differently than the one it replaced, but was a perfect fit in the clips.

Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled ... Read more in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.