My Orders
KUDC01 KitchenAid Dishwasher - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Upper Rack Wheel Mount broken/Upper Tray Loose
10 of 14 people
found this instruction helpful.
-
SAMUEL J from CALIFORNIA, MD
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
The Upper Rack Wheel Mount (where wheel attaches to mount) had broken. Was able to band-aid until parts received by running a small bolt and nut (with sufficient size washers) through the wheel attaching it to the assembly, then re-attaching the Upper Rack Wheel Mount back to the dishwasher upper tray. Once the part ordered from PartSele
... Read more
ct arrived, it was a simple matter of mounting the new Upper Rack Wheel Mount to the tray, replacing the band-aided item. The upper tray did have to be removed from the slider bars - required the plastic keepers on the end of the slider bar to be removed and then reinstalled once the Upper Rack Wheel Mount was replaced.
Read less
Was this helpful?
Thank you for voting!
blinking light above cancel button
10 of 14 people
found this instruction helpful.
-
Damion from Plant City, FL
- Really Easy
- Less than 15 mins
I replaced the electronic control board,
Was this helpful?
Thank you for voting!
door spring cable broken
8 of 8 people
found this instruction helpful.
-
garret from Fair Haven, NJ
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
You need to pull the unit out to get access to the spring connected to the rear leg frame. Use the everything in the kit. The rollers are upgraded and will guid the cable better.
Was this helpful?
Thank you for voting!
Surprise, I'm not a plumber - replacing impeller and seal kit 8193951A
8 of 8 people
found this instruction helpful.
-
stephen from REDMOND, WA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
When the top rack stopped cleaning, I tracked down the problem to the food shredder/chopping blade, and then to the impeller that drives the blade. The knob on the impeller had sheared/broken off. That meant removing the motor, and replacing the impeller. Four hours, a band-aid, and a trip to Home Depot later, here are my suggestions
... Read more
r />
1. Look for videos – this site is awesome, but they don’t have a video on this particular repair. I found 4 that got me close to knowing what I was doing.
2. Do all the “remove internal stuff” - you had to anyway to find the issue with the shredder/cutting blade
3. Take pictures as you move along, you’ll need them when you have to remember the placement of the water line, drainage hose, wired connections etc.
4. You need a 1/4 inch socket set. A 3/8 drive will NOT work (it won’t fit between the shroud and the base). Don’t start working on the repair, unless you have a 1/4 in socket with about a 6" extension
5. Someone at Kitchenaid should be shot for having the waterline connection facing the back of the unit. Use a short adjustable wrench
6. The order comes with a washer, but when you take the impeller off this model, you’ll see you don’t need it.
7. Placement is everything – there was zero clearance between the bottom of the unit and the floor. Placement of the water line, drain hose, and power line was critical – had to re-position the unit about 7 times to get it to “play nice”.
8. Hindsight – only needed to remove the wire harness for the motor (take pictures)
9. Hindsight – gloves are a great idea – sheet metal is unforgiving
1. Look for videos – this site is awesome, but they don’t have a video on this particular repair. I found 4 that got me close to knowing what I was doing.
2. Do all the “remove internal stuff” - you had to anyway to find the issue with the shredder/cutting blade
3. Take pictures as you move along, you’ll need them when you have to remember the placement of the water line, drainage hose, wired connections etc.
4. You need a 1/4 inch socket set. A 3/8 drive will NOT work (it won’t fit between the shroud and the base). Don’t start working on the repair, unless you have a 1/4 in socket with about a 6" extension
5. Someone at Kitchenaid should be shot for having the waterline connection facing the back of the unit. Use a short adjustable wrench
6. The order comes with a washer, but when you take the impeller off this model, you’ll see you don’t need it.
7. Placement is everything – there was zero clearance between the bottom of the unit and the floor. Placement of the water line, drain hose, and power line was critical – had to re-position the unit about 7 times to get it to “play nice”.
8. Hindsight – only needed to remove the wire harness for the motor (take pictures)
9. Hindsight – gloves are a great idea – sheet metal is unforgiving
Read less
Was this helpful?
Thank you for voting!
Broken bottom rack
8 of 9 people
found this instruction helpful.
-
Charles from CONVOY, OH
- Very Easy
- Less than 15 mins
-
Screw drivers
Removed old rack and and removed old rollers and installed old rollers on new rack as they work better than the new rollers sent with new rack
Was this helpful?
Thank you for voting!
motor making a load noise
8 of 9 people
found this instruction helpful.
-
Kenneth from Houston, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
pull out the dishwasher
lay it on its side
use a 1/4" drive socket with extension and a universal joint to undo the the hidden bolt,
twist the motor 1/4 turn. this is the hard part you have to pull fairly hard and rock the motor around a little to get the o-ring to let the motor slide out.
lube up the new motor with j ... Read more et dry or soap and insert back it, turn it back 1/4 turn, install the bolt and plug the motor control wires back in, then reinstall it back under the counter
lay it on its side
use a 1/4" drive socket with extension and a universal joint to undo the the hidden bolt,
twist the motor 1/4 turn. this is the hard part you have to pull fairly hard and rock the motor around a little to get the o-ring to let the motor slide out.
lube up the new motor with j ... Read more et dry or soap and insert back it, turn it back 1/4 turn, install the bolt and plug the motor control wires back in, then reinstall it back under the counter
Read less
Was this helpful?
Thank you for voting!
Leeking dishwasher
8 of 9 people
found this instruction helpful.
-
Lew from Lewiston, CA
- Really Easy
- 15 - 30 mins
Grabbed old seal and removed it.(notice how seal was situated in slot)
Pushed new seal in slot that held old seal. close door.
If dishwasher still leaks you put the seal in backward (I did!)remove seal reverse it and reinsert it.
Pushed new seal in slot that held old seal. close door.
If dishwasher still leaks you put the seal in backward (I did!)remove seal reverse it and reinsert it.
Was this helpful?
Thank you for voting!
Stopped washing in cycle, LED code flashed 6 times
9 of 12 people
found this instruction helpful.
-
Brendan from Indianapolis, IN
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
Since I had manual from initial installation I knew code meant heater was malfunctioning. Went to Sears, Lowes..no parts to repair. Instructed to go to appliance repair shop, closed of course...ordered online instead here and received in 2 days. Repair took 20 minutes. Super easy! Do not attempt to use adjustable wrench to tighten, use so
... Read more
cket set as plastic electrode casings will be compromised. Takes some tork. Probably saved $100-$150 repair call. Wife was pleased. I was suprised how easy.
Read less
Was this helpful?
Thank you for voting!
dishwasher wasn't fully draining at end of cycle
10 of 15 people
found this instruction helpful.
-
Richard from Naperville, IL
- Easy
- 30 - 60 mins
-
Pliers, Wrench set
Removed drain hose to ensure no blockage in drain. No blockage, then removed drain pump cap (where drain hose attaches to drain pump) with allen wrench. Push tab in on drain pump and twist counterclockwise, drain pump came off. Reversed to attach new pump and it works.
Was this helpful?
Thank you for voting!
No power to the front panel
7 of 7 people
found this instruction helpful.
-
Henry from Bellevue, WA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Checked the house circuit breaker, verified AC to the box under the dishwasher, removed the screws around the inside door cover, and removed the cover. Removed the outer circuit board cover. Used a multi-meter to verify AC to the door latch, and to verify the latch switch was working. Verified AC to the thermal fuse above the circuit b
... Read more
oard when the door latch was closed. Verified no AC on the other side of the thermal fuse. Removed the thermal fuse connections with pliers. Used thin flat blade screw driver to unsnap the thermal fuse assembly. Used multi-meter to verify no continuity through the fuse. Ordered the fuse assembly and replaced. Reconnected the thermal fuse connections. Manually closed door switch and saw lights on the display panel, and dishwasher started. Replaced all covers and works great.
Read less
Was this helpful?
Thank you for voting!
No power to dishwasher. Quit mid-cycle.
9 of 13 people
found this instruction helpful.
-
Jon from Bend, OR
- Really Easy
- Less than 15 mins
-
Screw drivers
Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.
Was this helpful?
Thank you for voting!
Door would not latch.
7 of 7 people
found this instruction helpful.
-
WILLIAM from BUENA pARK, CA
- Easy
- Less than 15 mins
-
Screw drivers
Partial disassembly determined thar the plastic handle was broken and a tensnioning spring was missing (had fallen out of reach within door) Ordered new replacement parts and received next day. Great delivery service. Installed in short time by removing four screws, disconnecting two wires and reversing procedures to reassemble. Findi
... Read more
ng parts on line was a great help and the delivery service was great,
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Third level spinner fell off
9 of 13 people
found this instruction helpful.
-
Brandon from Antioch, CA
- Easy
- Less than 15 mins
The part snaps on using two plastic retainers (included). You have to pull down gently on the feed tube at the top of the dishwasher to set the top retainer. After that it's a piece of cake.
Was this helpful?
Thank you for voting!
Dishwasher would not start
8 of 10 people
found this instruction helpful.
-
James from Norwich, CT
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Upon replacing the circuit card I found that one of the connectors was burnt. I fixed the connector and installed the new card, but it itermittantly still does not work. I think that the micro switch may be defective.
Was this helpful?
Thank you for voting!
quit pumping water
7 of 7 people
found this instruction helpful.
-
Robert from West Middlesex, PA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I removed the dishwasher from under the counter. This took the bulk of the repair time along with disconnecting the water supply and electrical connection. I had enough slack in drain hoses that I could turn the dishwasher over to replace the motor. I was surprised that there was only one bolt that held the motor in place. I put the moto
... Read more
r on, turned the dishwasher upright and slide it back unde the counter and began the long process ofreconnecting everything. I am sureit could have gone faster if I were younger and did not need glasses for close work. Start to finish took me four hours. This was the fourth time I have replaced motors in dishwashers of various makes.
Read less
Was this helpful?
Thank you for voting!