KUDA23 KitchenAid Dishwasher - Instructions

Tranfered wheels from old rack to replacement rack. Silverware caddy was a bit too big for the replacement. I gently bent the prongs on the rack a little and its fits perfect.

I ordered all new axles even though not all of them were broken - I figured it was just a matter of time. Ordered one new roller because one was missing, and an extra one just in case. Removed all old rollers and axles. A couple of them did not want to come off, so I "hit" them with a screwdriver. Put on all new axles and replaced the r ... Read more ollers. The whole project took about 10 minutes. SUPER EASY. CHEAP FIX FOR MY OLD DISHWASHER.

The website had great pictures, I compared the wheels I had and the broken axles with the pictures, and picked what I thought would match. They were perfect. I used pliers to pop the axle on, and my fingers to put on the wheels. It works perfectly now

I searched for the 18x5x5 insulation.,ordered it from Part Select. Waited. Company sent wrong part. Called, they gave me a refund, reordered, promised 2 day free shipping. Waited more than a week, paid for 2 day shipping. Received same, wrong part. Still don't have repair done. Looking elsewhere for part.

FIrst I shut the water and power off. I took 4 screws off bottom panels of dishwasher. Using pliers I move spring clip of the rubber valve. I disangage the hose and disconnected electrical connection ( two wires ) . Then using two open wrenches ( 3/4" and the other probably 13/16" - not sure ) disconnected the copper tubbing. I replaced ... Read more the valve i reverse order.I used teflon tape for sealing connections . Everything works good now.

I took out the bottom rack, turned it upside down, popped off the wheels and saved them and put on the new axles. It took a little doing to get the new axles snapped into place-they were stiff. I finally figured out how to use the pliers at the right angle to pop them on. Then the wheels popped right on and off I went.

Repair was awful without instructions. Instructions were requested twice with no response. Attempted without instruction and broke the sleeve. Reordered but not through Partselect

Repair went exactly like the video i watched online. Perfect

Closed water supply--Turned circuit breaker off to dishwasher--removed lower panel on dishwasher--removed the two wires from water inlet valve--disconnected water supply line--removed angle fitting from old valve & installed in new valve--reinstalled new valve & connected water line & 2 wires--This fixed problem.
I ordered part 11:0 ... Read more 0 1/15/09--Recd. new one 10:30 next morning. VERY FINE SERVICE & PRICE from PARTS SELECT.COM--Thanks.

I replaced the seals per the video instructions.

Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.

Finally listened to advice of others online and decided to replace inlet valve. Btw, the problem is NOT the inlet screen. It was completely clean in my case. Issue is with internal seals that swell over time and restrict flow leading to low water level.

Unplugged unit, removed lower front panel (two screws on outside upper c ... Read more orners), undid compression fitting on inlet supply line, removed two screws holding valve bracket to frame, disconnected electrical connections to valve, used pliers to compress hose clamp to remove valve outlet hose, used adjustable wrench and some elbow grease to remove small inlet elbow (its on tight!) from valve inlet, put teflon tape on elbow threads to reinstall on new valve, reverse removal instructions to put everything back. All done! MUCH cleaner dishes!

First I had to buy a new tray. I tried to remove the wheels from the old tray but they wouldn't come off without breaking. I ordered new wheels and axels and they went on fine with the aid of a C-clamp. Then I tried to remove the old bumpers but they broke when I tried to remove them.
So, I ordered two new bumpers. When I did I saw t ... Read more hat another user had posted a note saying that the new bumpers slipped on well if heated in hot water first. So, I heated them in hot water and they slipped on easily and safely.

watched a video

Took off old hose. It practically fell off.
Used a spoon to widen the ends of new hose and twisted on one end, then other end slipped on. Done!