KUDA22SWWH0 KitchenAid Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
rubber water tube disintegrating
I ran the tube under warm water and it was very easy to connect. I would have done it a lot sooner if I had known how easy it would be to find the part and install it.
Parts Used:
-
James R from Springfield, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken wheel
The hardest thing was getting the old one off and easy snapped the new one on
Parts Used:
-
Kay from Quitman, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water delivery tube to overhead sprayer punctured from age
I removed the roll out top wire rack of the dishwasher, turned it over and pulled the old punctured water supply tube off the force fit connectors on each end. I put a small amount of vaseline lubricant immediately inside the mouth of the new tube at each end. I pressed the ends of the new tube over the force fit connectors and tested them by shaking the pipe. I replaced the rack and fastened it into place.
Parts Used:
-
Mike from Oakland, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hose kept slipping off - stretched out of shape from use and age.
Used a heat gun (or hair dryer could probably work)to stretch the ends of the hose to slip over areas to connect.
Parts Used:
-
Barbara K. from Lorain, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the delivery tube was worn out with holes
the tube slid off and I used some liquid soap to spread on the end of each tube and I slid the new tube back on with ease and the upper rack of dishes now get cleaned/rinsed.
Parts Used:
-
Elwood from Battlecreek, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
hose had blown a hole
just popped the old hose off and put the new one on. the part was shipped very quickly and I received it within a week even during the holidays
Parts Used:
-
Debra from Windham, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water tube split and fell on drying element
Removed old tube, moistened both ends of new tube with hot water and slid over inlet and outlet holes. Repair done!
Parts Used:
-
Alan from Spooner, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
hole in the tube, wear and tear on it
I removed the old tube--I had taped over the hole. I didn't quite have the hand strength to fit over the ends and push the new tube into place. So, my husband did that at both ends without a problem. I'm relying on PartSelect for when I need parts for my 13 year-old appliances.
Parts Used:
-
Merdell from Montgomery, TX
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dishwasher did not do its job well.
It was simple. I simply replaced the old water tube with the new one you sent, and it works like new. Piece of cake.
Parts Used:
-
Wendell from Fish Creek, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher not cleaning as rubbr water tube cracked
I removed clips on the end of the rack, removed the rack, and pulled old tube off. Used plain water as a lubricant to ease replacement of new tube on the dilated end. Very easy!
Parts Used:
-
Janice from Napa, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the rubber tube was falling apart
In my case the rubber tube was so worn that it came off very easily. I removed the tube, then with a little cooking oil, I lubricated the new hose and easily slipped it into place. Now my dishwasher works great! I ordered the part received it and repaired it for less than $20.00 and in less than 15 minutes.
Parts Used:
-
GLORIA from HASTINGS, NE
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Worn out water tube.
Took old one off and put new one on, about a 4 minute job.
The part was about 1/3 of the cost if I had bought it local.
The part was about 1/3 of the cost if I had bought it local.
Parts Used:
-
Daniel from Nine Mile Falls, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old water tube had worn through and was falling off.
Removed old water tube and replaced it with the new one. Hard part was logistically trying to put it below the rack and it obviously it had to fit very tight and it was quite difficult to get in place, but I did it! Thanks to your easy to use website and excellent service. I was proud of myself for doing the whole job start to finish, and my husband was even more impressed. Only downside to that is that I think he'll be playing more golf, while I do the repair work from now on.
Parts Used:
-
Corinne from El Granada, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Water Coming Into Dishwasher
Repair was fairly easy, had to swith the mounting bracket from the old valve no problem. Install reconnected the water and the dishwasher works great now!
Parts Used:
-
DANNY from MORONGO VALLEY, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rollers and axels were worn out.
Very easily!! I am 19 years old and repaired the dishwasher for my grandmother in about 15 minutes. Great products.
Parts Used:
-
Shirley from Tucson, AZ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!