KUDA22SWWH0 KitchenAid Dishwasher - Instructions

PartSelect web page helped me determine the problem and the solution. It took me longer to read the fix-it directions than it did to fix the dishwasher. Just push the part in the hole and twist. When my wife got home she was so impressed that it was fixed and we didn't spend a huge amount to have a repairman come to our house. I got so mu ... Read more ch prasie that I didn't tell her how easy it was to do the repairs

First I removed two lower panels at bottom of dishwasher beneath the loading door using nut drivers. There had been a problem in that the dishwasher was not filling with water during any of the cycle. I closed the water supply. I removed the old water inlet valve completely using pliars to open the hose clamp at the outlet anbd remove th ... Read more e hose. Then used a I/2 "" wrench to remove the copper inlet line. Then I used a screw driver to remove the inlet valve mounting screws. I put the valve in my garage vise to remove the pipe fitting. Everything was reusable on the new valve. I just cracked opened the water supply to make sure water pressure was available to the valve inlet side and reassembled everything. Started the dishwasher and problem solved.

The dishwasher was so old that the new panel was too large. So I had to cut it down. This steel panel was so tough to cut that I used every cutting tool I had to trim it to the right size.

Fairly simple to replace the valve. Water input side was a rubber hose that required pliers to squeeze the ring seal and slide it down the hose. Copper pipe on the output side was attached with a 3/8 compression fitting.

I did need to transfer a brass elbow from the old part to the new one.

I was about to pull out my dishwasher and then removed the bottom cover and there you could see the spring. BUT WHO KNEW THERE WERE TWO SPRINGS? Only one of mine was bad BUT I would have replaced both of them at the same time. The diagram on the website clearly only showed one spring and now to buy the second one would cost more

First I tried duct tape until I could figure out how to get the part. I went online and found that part that I thought it was, but I wasn't sure since the tube I had was very stiff and looked like it had a particular shape on each end..the one on the site was just a straight tube. I removed the old part which was easy, it pretty much fell ... Read more off and then pushed the new one on and it conformed to the ends needed since the rubber was soft. It was so easy and the machine works really well again!

I first removed the old rubber water delivery tube ( not hard to do since it was literally falling apart from age). I then used a blow dryer to make the new rubber water delivery tube a little more flexible. I slid it on one end and then the other. My dishwasher works great now. The part was very reasonable ($15 with tax & shipping). ... Read more Last month I had paid Sears to come out to just look at my washing machine and it cost $139. Then the part was going to cost $200 with another $139 because they would have to come out again. I ended up buying a new washer. I was so excited that I was able to fix my dishwasher, I've been telling everyone.

Srewed it back on. . . Very simple!

Had to cut one end of old tube off with pocket knife, other end was cracked and came right off. Put a dab of vasoline in each end of new water tube and slid in place. Wife had called a repair shop, was told $25.50 for part, $65.00 house call/labor. Easy fix with 15.00 +/- part and 10 min. of my own labor.

pulled old actuator base off, followed instructions on how to install new actuator - followed them -
piece of cake.

Thanks

I was told I needed a whole new dishwasher arm, that I probably would not be able to change myself. Described the part of the part in your description area and lo and behold, there it was..
Could not find it anywhere else.
Very proud of myself for fixing it. I did not need any tools. Just removed the old corroded tube and attach ... Read more ed the new one.
thanks so much for the web site images and descriptions. (And I normally am very computer /technology challenged) Very user friendly site

I followed advice already posted and applied some liquid soap inside each end of the tube. Perfect!

Hello -

Upper rack fell down unexpectedly one night while loading the dishwasher -- evidentally the rollers had been deterioraring for a long time.

Orderd the new ones from you folks and installed them.

The problem I had was not with the replacement parts received, but making sure they were the correct on ... Read more es 'on line', ( called as well ), and then not having a thin enough wrench to hold the nylon nut while unscrewing the bushings which required a large width screwdriver.

I have already sent you an e-mail saying how happy I am with the new pieces.

Just another example of how the right tools can make everything go a lot smoother, but we everyday consumers often don't have them.....

Used duct tape to hold the old tube in place until I had a chance to see if the part was available online. Found it, ordered & received it the very next day. (Great service!) Removed the old tube which was already half off once I removed the duct tape & slipped the new tube on. A little trouble at the rounded end, but I used a screwdri ... Read more ver handle to kind of mold that end round & then slipped on.

Piece of cake --after having read what others had suggested on your webpage, I used the heat from a hair dryer which made the piece pliable and simple to fit into place. It took less than five minutes. When my husband came in from work, I proudly told him the part had arrived and it was fixed! Taa Daa!