KUCC151L KitchenAid Trash Compactor - Instructions

I had replaced the actuator lever several times before and was very happy to see that they finally fixed an obvious design flaw. The installation of the modification kit is fairly involved and does require removing the compactor and partially disassembling it. However, the instructions provided are very clear and the job was completed wit ... Read more h no complications. The fix they have devised looks like it will permanantly fix the issue. I'm very happy not to have to deal with the broken actuator issue ever again.

Laid appliance on side - removed top sheet metal cover and bottom sheet metal cover. Broken delrin ring gear was on bottom of bottom cover (housing). Gear had broken off of its hub, which also was the sprocket chain drive for both acme screws driving the compactor platten. Motor had to be loosened so that the chain could be removed f ... Read more rom the old sprocket hub, and the new delrin ring gear - with new sprocket hub attached - could be mounted on its fixed spindle. With new delrin gear/chain sprocket mounted, the motor had to be spaced and tightened to allow 0.010 inch lash between the gears. The only instructions included with the new gear was how to do this - by placing a piece of paper in between the pinion gear on the motor, and the new ring gear, and then tightening the motor into place. This was done, the sheet metal covers were re-installed, and the compactor works just fine. There is a design flaw in the original (KitchenAid) engineering of the gear, however, and I expect that in the next four years this will probably happen again.

provide or encourage a 1/4" box wrench and a Phillips screw driver along with drill and appropriate drill bit. Tape to hold in place template before drilling...critically helpfull

I removed the unit from under the kitchen counter by first pulling the trash drawer all the way out and lifting it out of the track and setting it out on the floor. I then slowly pulled the compacting unit out and unplugged the cord from the electrical outlet. With the entire unit out in the floor I took a nut driver and removed the screw ... Read more s from the top plate and the screws from both sides at the bottom of the front housing. This allowed access to the directional switch. Two screws on the right side of the switch have to be removed to remove the switch along with two holding plates on the left side of the switch. The switch can then be accesses for removal. Several wires are attached to the switch and should be removed one at a time and installed to the identical identical location on the new switch. The new switch can then be installed by aligning the holes and reinstalling the holding plates. When this is done the front frame and top plate can be replaced with the nut screws. Plug back into the electrical outlet and see if it works. In this case it did exactly what it was doing before I started. So either I did not reinstall the directional switch properly or I am in the one percent rather than the 99 percent that should successfully solve the problem as suggested in the trouble shooting guide. I will now recheck the installation of the directional switch nd then check the bottom of the unit to see if the gears or chain drive are broken .

After removing the compactor from under the counter, and unplugging it, I did the disassembly. The replacement parts were easy to install. Two holes had to be drilled to mount the switch, but that was not difficult. Overall, the instructions were easy to follow and the parts all fit.

Went well but took time. Instructions adequate but not detailed.

The online repair states the repair could be done in 10-15 minutes and actually took over an hour. It would have taken 10 minutes if I could have just purchased the metal flange that broke.

This replacement kit did solve the problem but required replacement of a number of parts because the switch and actuator functionality had been redesigned. Fitting the kit of parts requires that you have to slide the compactor away and out of its location (might be a bit tricky if it's beautifully integrated into a designer kitchen)so as ... Read more to remove the front cover. Some heavy leather gloves could be helpful here since there are several sharp edges on the pressed steel carcase of the unit. Once free the kit replacement is relatively easy (for the average handyman/woman), following the simple instructions provided. You will need to drill two new holes in the front plate (template provided) so an electric drill and a sharp drill bit (for metal) will be needed. Most important - the kit worked; and with a more reliable component than that replaced.

Thanks to Parts Select and their detailed instructions it turn out great! Replacement Parts fit Great!

followed the instruction sheet. Instructions should be expanded to tell novice more about each step. Instructions should point out that the old switch is not easy to remove, and may break during removal. Instructions should point out importance of noting which of the two switch wires are connected to which temminal on the new switch. Inst ... Read more ructions should warn installer that the metal console and compactor frame are very sharp and can cut hands and fingers-use gloves during switch removal and re-installation. Instructions should note that drill size should be larger. I used 7/64", and still needed to enlarge hole for screws to insert. Instructions need to emphasize that the new actuator pedal assembly screws supplied have a very small phillips head slot. If the hole drilled is not large enough, there is a possibility of stripping the screw slot.

All I really needed to do was to take the front facing off and put on the new container, but I took the opportunity to do a complete overhaul and cleaning. It now work like a new compactor.

Followed PartsSelect instructions, the Compactor was appoximately $1000. when I purchased it. The kit was $26.14. I will forever be a customer of this company. Thank you, Brian

First off....I was surprised at how inexpensive the drive gear kit was. As others commented, they fit perfectly and I believe will fit other manufacturer's models since there is a lot of cross branding. The Drive gear replacement itself would be easy as described by others so I won't repeat that. However replacing the plastic tubular " ... Read more ram stops" on the screw drive was a challenge since there are no "helpful hints" in the blog. To do that you have to work from the top and sides. Needed to remove the two gear cams where the screw drives are seated on the bottom of the unit, then (working with the unit on it's side)you have to raise the whole (heavy) plunger that is attached to the drive screws high enough to remove the old tubular ram stops and bushing and replace. To raise the plunger assembly out from the top you have to remove the sheet metal top plate of the unit....and....importantly remove the control panel on the front where the switches are. There is a limiter switch that has a metal arm which engages a plate on the plunger to stop the unit when it reaches the top. You need to remove that switch to be able to raise the plunger assembly high enough to get the new parts on the screw drive. Put all that back together and then go on to the gear replacement as described by others which was straight forward. Very messy job with all the grease and garbage residue. I am pretty handy figuring these things out, and there may be an easier way, but next time I will call a pro or replace the whole compactor.

Replaced drive gears.They arrived in a kit from Parts Select with instructions.They fit perfectly and the compactor works like new.

Looking at the information I found online it was either one of 2 things the directional switch was bad, or the drive gear was broken. I replaced the directional switch 1st since that was the easiest and that did not solve my problem. I put it all back together and thought about it for a little while. After a couple of days. It occurre ... Read more d to me that I could see the ramrod's spinning as the plunger goes down, then when the plunger reached as far as it would go. The ramrod's would stop spinning. I reasoned that the problem had to be somewhere between the motor and those rods when I opened up the bottom of the trash compactor, Iran the cycle again and I could see that the drive gear was still spinning, but the chains to the ramrod's were not spinning. Once I saw that I realized that the sprocket that was attached to the drive gear had broken. The sprocket is metal and the drive gear is plastic and they fit together perfectly, but through age or stress. The plastic have become rounded and no longer fit perfect on that nut when you applied a good deal of pressure. I didn't have the tool that I needed to replace the small drive year. I think you need some kind of a punch to get that pin out. So I left that one in place loosened the nuts that hold the motor in place to create some slack in the chain chain came off the new drive gear one on. I tightened the motor back up in the correct position is reassembled everything and it's working perfect again.