KUCC150 KitchenAid Trash Compactor - Instructions

Simply removed the two plastic gears (held on by some sort of clip), put the new gears in place using the spacing instructions that were provided in the kit ....... and it is working!

I have always used compactor bags made of paper & plastic. I was sent bags made of only plastic. I called and was told that is the only kind available. I am concerned that the plastic bags may not be strong enough.

I quest I will have to try these all plastic bags. I hope they are strong enough and work properly.

Took top off of the unit, then the 2 protective covers, Lifted Power ram out. Installed protector and new gear nuts. Reassembled... Done job. Great schematics and part list from Part Select./ Good delivery time as well. Will use again.

replaced rotary

-Removed the forward sliding rail screws...lifted the rails up several inches to access the wheel assembly...bent back the steel tab to access the nuts holding the wheels to the frame...replaced the wheels and bent back the steel tabs to original position. Trash bin now rolls out completely as before

Removed 4 screws and the foot release to attach the new guard. Replaced the foot pedal and 4 screws and was done.

I removed the unit from under the counter. After removing all of the bits of old trash and making sure the chain and gears were not slipping or striped, I knew it was the power nuts on top of the ram. After all of these years they were worn out, almost smooth inside where the threads are. They were easy to locate on your website. I receiv ... Read more ed them in 2 days (faster than expected) and in 10 minutes the unit was back together and working well. Today was the first bag to be taken out after the repair, it is much heavier than the previous ones, a sign that we are now packing much more trash in a single bag!

changed out the switch and that fixed the problem

The first panel I received was scratched and had to be replaced. I called PartsSelect and they sent a replacement.

An easy replacement that made the compactor look like new, that is important since we will be selling the house.

This new one from part select I think fit better than the original so all I had to do was install the handles as the depiction on the packaging showed and install it. Less than 1 minute.

First thing I did was put the unit on its side and removed the bottom to access the broken plastic gear that moves the chain that drives the compactor up and down...There I was able to manually move the chain by turning the nut with pliers and moving the piston up (painfully slow) until I could at least use the bin for trash while I waite ... Read more d for the replacement part to arrive. Once I had the part I loosened the four bolts that allowed the drive gear to move a little and slacken the chain - I then put in the new gear - make sure you have the proper spacing and washers - my replacement kit didn't have any washers so I resused the old washers and all seems to be working well!

layed it in the kictuchen floor took of bottom and changed the gears that's all there was to it piece of cake

REMOVE COMPACTOR DRAWER
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES

Bought wrong roller. The drawer roller is different than the stationary rollers. Note the difference.

I held up on the compactor ram as i loosened the two screws on each of the two retaining cups. I then unscrewed the threaded bushings and lifted the ram out of the unit. I then cleaned the surface of the tracks on which the ram guides up and down and applied a thin layer of silicone grease to those surfaces as well as the threaded rods ... Read more . . I placed the ram back into the unit and held it in place as i replaced the threaded bushings and their respective caps. Unfortunately i neglected to move the limiting switch that stops the ram when it reaches the top of the cycle and I broke the lever that contacts the ram and subsequently activates the stop switch. so i removed the ram and removed and inspected the switch. It was broken beyond repair so i ordered a new switch from the same place I purchased the threaded bushings and am waiting for them to arrive. Lesson learned, pay attention to the sequence by which the original parts are removed and understand how the system functions so that you can remember to put it back in the right order.