KTTS505ESS2 KitchenAid Trash Compactor - Instructions

At best it is advisable to load just one at a time and covered with newspaper etc., In this case someone put in three bottles with out covering with heavy newspaper etc.and for some reason one rode out and to the side. Crushing the side of the metal trash container. This pinned the container against the side of the compactor body and behi ... Read more nd the front rails. Using a lot of pulling and some nifty pry bars and two hours of prying and squeezing we got the container out( see attached photo )The replacement container was ordered on a Sunday night and arrived Tuesday morning. Removal of the existing front panel ,foot pedal and door switch was easy and installation on to the replacement container was a breeze with a little orientation required to line up the switch and pedal in the right configuration. 20 min tops and that was with five kids helping ;)

Replaced the limit switch. This did not alter the problem. Took off the On/Off/Start switch and dissasembled. I found the the Start switch was stuck in the on position. I reassembled the switch mechanism assuring that the Red "ON" indicator moldings were correctly positioned and reassembled everything. The Compactor now works properl ... Read more y. Need to add "Check the Start switch" to diagnosis.

Replaced drive gears.They arrived in a kit from Parts Select with instructions.They fit perfectly and the compactor works like new.

changed out the big gear that was broken

Compactor ram was stuck in the down position after hearing a loud bang during a compacting cycle. Removed outer compactor casing to determine cause, only to find gear housing underneath the compactor that contained drive chain and gear assembly. Primary gear had split neatly in half. Determined the appropriate part needed with partsele ... Read more ct part finder (of course, an entire kit, and not just the gear), had part shipped and had compactor repaired in three days. The actual repair and reassembly of the compactor took less than a half-hour. Consisted of removing chain tension from gear hub by loosening four sheet metal screws holding motor assembly, removing circlip and old gear hub from chain and shaft, replacing gear hub with new part, lubricating the gear mechanism, and reinstalling in reverse order.

Ordered new door hinge and used available You Tube Video. to assist in installation. Not a very difficult job, however that did not solve the problem. Then in an attempt to complicate the solution, I again removed the door and took the entire inside cover off. The entire latch mechanism fell on the floor. It took a very long time to det ... Read more ermine how the latch mechanism was placed. Finally with the help of a neighbor the latch was placed back into position, the glass and screen replaced and finally all the plastic molding seated and screwed tight. Guess what the latch now seated correctly and appears to work correctly.

I removed the unit from under the kitchen counter by first pulling the trash drawer all the way out and lifting it out of the track and setting it out on the floor. I then slowly pulled the compacting unit out and unplugged the cord from the electrical outlet. With the entire unit out in the floor I took a nut driver and removed the screw ... Read more s from the top plate and the screws from both sides at the bottom of the front housing. This allowed access to the directional switch. Two screws on the right side of the switch have to be removed to remove the switch along with two holding plates on the left side of the switch. The switch can then be accesses for removal. Several wires are attached to the switch and should be removed one at a time and installed to the identical identical location on the new switch. The new switch can then be installed by aligning the holes and reinstalling the holding plates. When this is done the front frame and top plate can be replaced with the nut screws. Plug back into the electrical outlet and see if it works. In this case it did exactly what it was doing before I started. So either I did not reinstall the directional switch properly or I am in the one percent rather than the 99 percent that should successfully solve the problem as suggested in the trouble shooting guide. I will now recheck the installation of the directional switch nd then check the bottom of the unit to see if the gears or chain drive are broken .

Laid appliance on side - removed top sheet metal cover and bottom sheet metal cover. Broken delrin ring gear was on bottom of bottom cover (housing). Gear had broken off of its hub, which also was the sprocket chain drive for both acme screws driving the compactor platten. Motor had to be loosened so that the chain could be removed f ... Read more rom the old sprocket hub, and the new delrin ring gear - with new sprocket hub attached - could be mounted on its fixed spindle. With new delrin gear/chain sprocket mounted, the motor had to be spaced and tightened to allow 0.010 inch lash between the gears. The only instructions included with the new gear was how to do this - by placing a piece of paper in between the pinion gear on the motor, and the new ring gear, and then tightening the motor into place. This was done, the sheet metal covers were re-installed, and the compactor works just fine. There is a design flaw in the original (KitchenAid) engineering of the gear, however, and I expect that in the next four years this will probably happen again.

Kitchenaid had a problem with its footswitch. It was a flimsy piece of metal that pushed in a switch. The flimsy metal part is no longer produced, and they have a replacement kit. The instructions provided that you pull the frame apart, but I was able to do it by coaxing out the old switch, reconnecting and inserting the new switch, and ... Read more then drilling and screwing in the new switch actuator. The old switch activated the unit when pushed in, the new switch activates the unit when let out.

First off....I was surprised at how inexpensive the drive gear kit was. As others commented, they fit perfectly and I believe will fit other manufacturer's models since there is a lot of cross branding. The Drive gear replacement itself would be easy as described by others so I won't repeat that. However replacing the plastic tubular " ... Read more ram stops" on the screw drive was a challenge since there are no "helpful hints" in the blog. To do that you have to work from the top and sides. Needed to remove the two gear cams where the screw drives are seated on the bottom of the unit, then (working with the unit on it's side)you have to raise the whole (heavy) plunger that is attached to the drive screws high enough to remove the old tubular ram stops and bushing and replace. To raise the plunger assembly out from the top you have to remove the sheet metal top plate of the unit....and....importantly remove the control panel on the front where the switches are. There is a limiter switch that has a metal arm which engages a plate on the plunger to stop the unit when it reaches the top. You need to remove that switch to be able to raise the plunger assembly high enough to get the new parts on the screw drive. Put all that back together and then go on to the gear replacement as described by others which was straight forward. Very messy job with all the grease and garbage residue. I am pretty handy figuring these things out, and there may be an easier way, but next time I will call a pro or replace the whole compactor.

Followed PartsSelect instructions, the Compactor was appoximately $1000. when I purchased it. The kit was $26.14. I will forever be a customer of this company. Thank you, Brian

All I really needed to do was to take the front facing off and put on the new container, but I took the opportunity to do a complete overhaul and cleaning. It now work like a new compactor.

Thanks to Parts Select and their detailed instructions it turn out great! Replacement Parts fit Great!