KSSS36QMB01 KitchenAid Refrigerator - Instructions

Removed the two screws that hold flaping door. Removed the single screw that covers the connecting wires. Disconnected the wiring plug. I wiggled out the ice maker. Took off the motor cover. Swapped out one motor for the other. Reinstalled the icemaker in the resverse order of removal. Note the wiring plug in the freeze is very fro ... Read more m. It makine s the reconnection differcult.

Googled with question about how to get to the repair as there were no screws on the faceplate. Found I had to lift the faceplate at the bottom and pry out. Was kind of hard to get the long spindle back through the ears of the bracket holder along with getting the spring of the door lined up for the spindle to pass through to the other si ... Read more de. Finally got it right and then just put it all back together. Frustrating at first but I had to get it done as my wife was tired of having to take large clumps of ice out of the ice tray..three years wait for the repair. That door being open let warm air in and let the ice melt just enough to stick together in a clump. All is well now. Longer you wait the more appreciative she is however. ha

Popped off the front panel(from bottom) removed two screws to remove old part and put everything on new panel. Put everything back in place all in less then 15 minutes.
Ordered parts Wednesday forenoon and received it Thursday morning. Very outstanding service!

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Online parts detail made identifiying the correct part very easy. $10 fix instead of a $150 service call. Once the right part was identified, fixing it was very easy.

Old part would not stay in place (broken). Recieved new part and snapped it in to place . No tools needed.

Removed screws, unplugged connectors to the two faulty circuit boards, reconnected both cables to new/replacement circuit boards, reinstalled screws. Extrremely simple! Worked perfectly! Saved about $150 in less than 30 minutes. Great, fast service by PartsSelect.

Local service person missed the diagnosis and advised $10,000 new refrigerator. I looked and saw that the switch was deformed and had burn marks. Searched for switch online. Found site Ordered. Part arrived next day. 5 minute job to replace. No tools needed. Refrigerator works great. Thank you t!

Remove the old part with pliers and pulled out used water filter Installed replacement water filter on cap and installed in grill area below door Hooray !

I watched the video this site has on their website and I did exactly as the instructor did. I had my ice maker fixed in less than 30 minutes. I had watched the video prior to receiving my parts so I already had the prep work done. I had the parts removed that needed removing and all I did was slide the new ones into place. Use the parts c ... Read more hart on this site to make sure you get the right parts and use the video to uninstall/install your parts. Do exactly like the instructor says and you won't have any problems. It was as my school kids say, "easy peasy". Thanks!!!

First I removed the 2 screws holding the cover on. I then disconnected the wires harness before removing the 4 screws holding the motor in place. I reversed these three steps and wala, the ice dispenser now works perfectly.
Thanks

Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .

took apart panel from door and removed old part and installed new part.It's difficult if you have big hands. Best if you have someone hold up wire panel while you are installing.

It was great repaired the problem for under $60

Removed two screws on inspection plate underneath second shelf on inside of the freezer door. Removed four screws holding motor that turns inside ice bin.
Unplugged wires and reinstalled.

Removed the drip tray under ice & water dispenser & removed 2 screws holding faceplate.
Unsnapped 2 microswitches that control ice dispenser & water dispenser.
Removed 2 screws holding control bracket, replaced with new one & reassembled.
Done!