KSSC48QVS03 KitchenAid Refrigerator - Instructions

Repair was replacing motor kit. I did not use the plastic parts - ejector arm and separator. Went same as others described. I had removed ice maker from refrigerator although this was not necessary to replace motor unit(Please unplug refrigerator whether or not you remove the entire ice maker).
Removed three screws, removed old moto ... Read more r unit, inserted new unit making sure the ice level wire arm end was in slot. Ejector is D shaped so can't go in wrong. Replaced screws and replaced ice maker in freezer. Note - be sure the water tube is in the trough before trying to refasten ice maker.
Added note: If for whatever reason you need to remove ice maker note that there are three mounting screws (others have mentioned this) Completely remove one under middle of ice maker. For the two at top of ice maker - just loosen a few turns. The ice maker can be lifted and pulled away from the wall without removing these screws. Also there is a tab on the electrical wire connector for ice maker at back wall of freezer. Tab must be depressed with a flat tip screw driver while pulling out to remove wire connector. Tab is on wide side of connector facing inside of freezer.

Repair worked. Have lots of ice again.

The repair went just as simple as the video on the web site. Parts came really fast. replaced in less than 15 minutes. i thought the icemaker unit was the bad part but after gettin info from this site it told me waht to check first and i found that the emitter boards were bad. Thanks for saving me the money on buying the wrong parts. also ... Read more bought parts the folowing week to repair my wifes kitchenaid mixer.

I did some research on the website and found out that there is a test with the sensor lights. When I looked at mine, they were not turning on or blinking when the door was openned.

The repair was very easy to accomplish and all I needed was a small philiips screwdriver. I unscrewed both left and right side panels covering the ... Read more circuit boards and pulled the connector off. I'd say the most diffcult part was lining up the connectors to the boards since there's not a lot of room because of the harness length. Once the boards were connected, they set in place easy and I put the covers back on.

A word of warning, it took the system about ten minutes until the cycle started and water started filling the tray. But aside from that, everything is working perfectly well.

I saved about $200 in service fees!!

Removed and disconnected the icemaker, cleaned all areas and disassembled the failed parts. Reassembled with the new parts inlcuded with the purchased package and resinstalled the unit. Started the unit and chedked for proper operation. Successful repair.

The ice maker would not fill with water. Water was available to in-door water dispenser. All signs pointed to the ice maker control boards. Ordered and replaced the boards. Within a couple hours it was making a new batch of ice every 30-60 minutes. The repair instruction video was a great help....made the repair a snap!

Go first to Kitchenaid web site and download their consumer services Technical diagnostics on the ice maker. Very well written and clear to follow. Instructions step you through interpretation of blinking code lights which is key to finding the real problem and leads you to repair the correct failed part. My diagnosis said to replace both ... Read more emitter and receiver. I replaced the emitter first and tried it and solved the problem I didn't need to buy the receiver but I have a spare part now. Do the diagnosis and save yourself some money. PartSelect got the parts to me quickly and saved me money compared to our local parts supply companies.

I first turned off the refrigerator. I then used a hair dryer to melt and release the ice by warming the bottom of the mould. Then I turned the fridge back on and let the icemaker discharge the ice. I then turned off the icemaker and ordered the new part. I unplugged the fridge, removed the icemaker (three screws and an electrical conne ... Read more ction). Then I replaced the heater/tray with the new one and turned everything back on. Within a couple of hours we began having ice again.

I had a son put in the new light bulbs. Rather simple

unscrerwed the broke part and screwed in the new one---5 minutes

Was not able to do the replacement because the part that was sent was broke. Tried to call multiple times and the recording said that you were not able to talk to human beings. I was able to get a refund approved, but did not get instruction on how to return the broken part.

Philips screwdriver
Removed screw (1)
Removed light bulb
Put in new light bulb
Closed door to bulb compartment
Returned screw.

Pro tip! Check how many bulbs you need before ordering. Mine only needed two. I got two. I suspect I’ll buy a new microwave before new bulb burns out again. Ordering/deliv ... Read more ery was fast. No need to have spare on hand.

Removed old filter and installed new filter.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Bolt off, bolt on. That easy. A few screws and an electrical plug and done. New unit works great and the cost of the unit was almost half what the repair service wanted to just come out.

Removed old ejector arm and installed new part.