KSSC48QTS03 KitchenAid Refrigerator - Instructions

Remove Ice bucket, Remove Phillips screw from bottom of coupling. replace washer, Coupling and screw. replace bucket. very simple.

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Simply cut the water tube on both sides of connector and push in the new one.

Unpluged the refrigerator, removed the burnt out switch by unpluging it, plugged the new one in re installed the switch into cover. Plugged in refrigerator replaced cover. Done. Easy as one two three

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80.. ... Read more .would have been at least $100 to have a repair person come to the house!

Very easy to order from parts select. Took seconds to replace.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

removed ice bin then removed 2 screws and removed broken button. replaced with new button and 2 screws. 5 minutes max thanks for quick response with part

Starting at the bottom, with a flat blade screwdriver pry the front cover off the opening. Unplug the wire connector from the back, remove the cover plate holding the switches and light socket by pushing out on the plastic clips on each side. Use something like a bungie cord to hold it up out of the way. Carefully unsnap the clear plastic ... Read more ice shoot from the push arm, next carefully unsnap the cover door from the push arm. Clean anything that needs cleaning (CLR works great on hard water deposits)
Install everything in reverse order, the cover door first, ice shoot next, switch plate, plug in the wire connector and snap the outside cover in place.

Sorry I didn't do the repair but my husband did. It took him about an hour and a half. He did have to take the main part of the ice maker out of the fridge and take a couple of pieces off t oslide the tabs from the stripper arm into place. It was great. Fixed the icemaker for $22.00 dollars with no service fee. I can't imagine what they w ... Read more ould have charged me.

Had to widen screw access hole in motor frame enough to use the phillips bit with my 12V impact driver. That worked perfectly. It took an extra two hours of trying to break the screw free without stripping it and figure out what to do when it wouldn't budge. Once I got the screw out the fix went quick and the ice maker now works great. If ... Read more you have a coroded screw go straight to the impact driver.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull t ... Read more he connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Easy repair, unplug the fridge and then remove the 3 screws on each side of the freezer holding the emitter and receiver. Swap the boards and re-install. Takes less than 10 minutes.