- Home
- KSSC36QTS02
- Instructions
KSSC36QTS02 KitchenAid Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
changed the light bulb still would not work so I figured it was the switch sure enough.
3 of 4 people
found this instruction helpful.
-
anthony from HAVELOCK, NC
- Really Easy
- 15 - 30 mins
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this helpful?
Thank you for voting!
Ice Maker Stopped Making Ice
3 of 4 people
found this instruction helpful.
-
Stephen from North Bend, OR
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replacement of parts was simple. But there are three main reasons that ice maker quits: door sensors stop working; ice maker, or it control system, stop working, or the coil controlling when water is released into the ice maker stops working. It was easy to replace the door senors; repairman replaced the ice maker and control board, which
... Read more
is located in one end of ice maker, but it ended up being the coil or simply a frozen water outlet into the ice maker that stopped the system from from working. The first thing you should do is to make sure that the water outlet into the icemaker is not frozen - use a hair dryer to melt frozen ice in the outlet - don't melt the plastic outlet with high heat. If the system still does not work go to this: look at red sensor on door to the the right. If it blinks twice in a couple of second with a time out and then repeats over and over, close the door on the receiving sensor on the left hand side of the casing and if the red light comes on steady then the sensor is working properly. So, now you have the coil that turns the water on and off or the water maker itself that can be bad. It will be one of these that are at fault, but not both. Call a repairman.
Read less
Was this helpful?
Thank you for voting!
ice maker quit working
4 of 7 people
found this instruction helpful.
-
thomas from galena, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
I ordered a new ice maker and replaced it. It hung on two screws in the side of freezer and connected to the electric in back by a plug in unit. Within 20 minutes we were making ice again. Awesome!!
Was this helpful?
Thank you for voting!
part was demage , old
6 of 13 people
found this instruction helpful.
-
Joao from Chandler, AZ
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
removed old part and instal the new one :)
Was this helpful?
Thank you for voting!
defective light switch
3 of 4 people
found this instruction helpful.
-
THOMAS from WILLARD, OH
- Really Easy
- Less than 15 mins
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this helpful?
Thank you for voting!
Refrigerator would not stop making ice
3 of 4 people
found this instruction helpful.
-
Joshua from Lawrenceville, GA
- Easy
- Less than 15 mins
-
Screw drivers
Easy repair, unplug the fridge and then remove the 3 screws on each side of the freezer holding the emitter and receiver. Swap the boards and re-install. Takes less than 10 minutes.
Was this helpful?
Thank you for voting!
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
3 of 4 people
found this instruction helpful.
-
David from Hemet, CA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull t
... Read more
he connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Read less
Was this helpful?
Thank you for voting!
Ice maker would not turn off. Kept making ice! Even turned off all water to house, but then realized that ice maker was being fed by pressurized RO tank!!
4 of 7 people
found this instruction helpful.
-
Keith from Green Valley, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver
Broken plastic part in motor assembly. Very simple to replace. Sears wanted $322.00!!!
Was this helpful?
Thank you for voting!
Ice Maker overflowing and forming ice blocks in cube tray
3 of 4 people
found this instruction helpful.
-
Nelson from Pasadena, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
The teflon coating on the ice maker had worn off in a section. This was causing the cubes to stick and the tray heater to have to run longer. Which meant that water would accumulate in the tray over several cycles, eventually spilling over on a fill. The hardest part about replacing the ice maker was getting the plug disconnected. I h
... Read more
ad to use a small screw driver to push the tab that latches it down while pulling the plug out. You only have to completly remove the lower mounting screw. The top two just need to be loosened enough to remove the ice maker.
Read less
Was this helpful?
Thank you for voting!
wouldn't make ice
4 of 7 people
found this instruction helpful.
-
John from Martinsburg, WV
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Just had shoulder surgery so had to use one arm. Was simple and easy. Just took out ice tray, loosed two fasteners at top, removed screw from bottom, pulled out partialy and disconected electric and removed old icemaker. Hooked up new electric and hung on two top fasteners, reinstalled bottom screw, tightened top fasteners and put ice tra
... Read more
y back in. Was making ice within a couple of hours.
Read less
Was this helpful?
Thank you for voting!
Wasn't making ice
4 of 7 people
found this instruction helpful.
-
James from Wadsworth, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
There are 3 screws the one on the bottom comes all the way out, the 2 on top just need to be loosened. Lift up on the ice maker to clear screws, pull away a little bit then while holding disconnect the wire harness from the ice maker by pushing down the locking tab with a flat head screw driver. Then reversed the process with the new on
... Read more
e, it took an hour or so but the ice started falling, a day later the bucket was full.
Read less
Was this helpful?
Thank you for voting!
ice maker quit making ice
3 of 4 people
found this instruction helpful.
-
Thomas from Sherrard, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
removed the LED covers on both sides of the freezer, unplugged each circuit board, plugged in both circuits, replaced the LED covers, job complete, making ice
Was this helpful?
Thank you for voting!
icemaker wasn't making ice
2 of 2 people
found this instruction helpful.
-
JAMIE from HANOVER, PA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we
... Read more
get many more years out of this icemaker.
Read less
Was this helpful?
Thank you for voting!
Filter applicator broke
2 of 2 people
found this instruction helpful.
-
Susan from AVON, CT
- Really Easy
- Less than 15 mins
Bought new applicator
Was this helpful?
Thank you for voting!
cap had broken notches
2 of 2 people
found this instruction helpful.
-
gina from HAMMONTON, NJ
- Really Easy
- Less than 15 mins
filter has to be removed and attached then inserted into rifrigerator
Was this helpful?
Thank you for voting!