KSSC36QMS02 KitchenAid Refrigerator - Instructions

I removed the ice bucket,the gear is located under the ice bucket and engages when ice bucket sits on it and turns the tray for ice to fall in the shute,2 screws to remove and the gear comes off and I put the new one on and put the screws back,very easy to do, total time 5 minutes,repair man wanted to charge $114 for the part and $100 for ... Read more labor,I did it all for $25 thru this site,I love this site,it gsaved me alot of money,thanks partselect.,

I removed the outer ice/water dispenser cover following directions I found on-line (push down and gently pry out at the bottom). I then removed several nut-head screws which were holding a plastic plate which had the door light and electric control wiring mounted in it. Behind that I found a broken tab on the Control Bracket which was w ... Read more hy my water dispencer was not working and I found the chute door for the ice maker was chewed up which allowed warm air into the chute and was causing my ice build up problem. Replacing the Control Bracket was easy. Just note how things come apart. Putting the chute door in was a little more complicated, but again, note how things come apart and you should not have a problem putting it back together.

Ice machine would not turn, dispense, or crush. Made ice fine. First, replaced switch for $7, did not fix it. Second, replaced motor for $80. Old motor was metal, new motor is plastic, but replaced it in 20 minutes, works like a champ. Inside freezer door, took off shelf under the ice maker, unplugged frig, removed two screws and cov ... Read more er plate, removed four screws on motor bracket, unplugged motor, plugged in new motor, replaced bracket and 4 screws, replaced cover, plugged frig in...Perfect!

I removed the Ice door front cover on freezer door. Found door pivot was broken. I installed door pivot bracket, and dashpot in kit. I used most of the kit to repair it. The door now works like new. Thanks for the right parts Frank

removed the three screw holding the broken unit - pulled off the old module.

Before I could install new module I had to loosen some fasteners on ice maker so I could turn shaft to align with new module.

Then push on new unit and three screws. Had tumbling ice in about an hour. My wife thinks I'm a hero. (I am)

At their site was ordering each piece by # and cost and it was adding up to be costly. Went to partselect and was doing the same and up pops the ice door kit. Was a little wary because my original had a heater tape to it. Got the kit and installed not a problem at all. 100% satisfied would recommend to anyone.

First off, if you have the stainless steel panel inserts on your refrigerator you'll need to remove those to do this repair. I kept looking for the access holes on the underside of the dispenser panel that you're supposed to insert a screwdriver into to pry it off. It wasn't until I removed the freezer door handle, slid the lower stainles ... Read more s panel insert out, and removed the rail just beneath the dispenser that I could see and access these holes. I also removed the upper stainless panel and rail just above the dispenser to allow enough movement get the dispenser cover off and out. The rest of the repair is pretty straightforward. The old ice door was beaten up and not closing completely, this was letting warm air into the freezer which was melting and re-freezing. This kit fixed the problem.

Looked at repair diagram, ordered part [ fast shipping ],first empty freezer pulled everything out removed rear panel, removed motor, installed new motor into housing. Using a heat gun [on low ] defrosted ice build-up on coils, this tookover one hour , reinstalled everything and it started right up but took 24 hours to stablize and get t ... Read more he ref / freezer back to the -10/37 degree . All better and quiet now. Last time I paid for the repair over $200 very happy thank you part select

Turned the lock knob on the filter and removed. put
lock knob on new filter and installed.

Very user friendly website, would highly recommend to anyone.

Removed the old filter (it screws out) an put the new one in!

Used pliers to help turn knob 1/4 turn to left removed filter; replaced with new filter.
Probably need new outer cap.

The repair was incredibly easy -
1. Turn off the water at the water line for the fridge
2. Disconnect the pressure fittings for both lines running to the resevoir.
3. Remove the old resevoir
4. Install the new resevoir and run the lines back to the orginal fittings.
5. Reconnect the fittings, turn on water.< ... Read more br />6. Drink water!

I ran all the ice maker module tests that I could find online, I tried cleaning the contacts inside the ice maker control module, nothing worked...so I finally decided to purchase a new control module. I had already had the module out and taken apart a few times, so the new one was very easy to install. Just removed the entire icemaker ... Read more from the fridge, removed a few screws, took off the old module, put on the new one, replaced the screws, re-installed the icemaker in the fridge (it just slides in and out similar to a shelf). And 30 minutes later I heard the first batch of ice cubes drop! And by morning the bucket was nearly full. After two weeks of no ice and trying to fix it myself - the family was glad to have ice again (it was July in NC!). In retrospect, I should have followed the advice I found online and ordered the new part sooner and saved all of those frustrating hours of trying to "fix" the part myself.

The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the pl ... Read more astic arm, which caused the arm to fail. Then reassemble in reverse order.

Remove the kick panel and simply turn the filter counter clockwise and it slips right out.Water shuts off when filter is removed.After new filter is installed be sure to bleed line thru the water outlet in door to clear air in system.When first water is bled the water will continue to run until line drains. Then comes the air.Bleed until ... Read more water is clear.Its an easy job and can save you$$$$$.Ray Palm Bch Fl.