- Home
- KSSC36MFS05
- Instructions
KSSC36MFS05 KitchenAid Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice maker was not working.
4 of 7 people
found this instruction helpful.
-
Doyle from Winchester, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
On my particular model refrigerator I only needed to remove one screw and disconnet the plug. I then slid the unit out. The new ice maker did not come with the plastic sled that was attached to the old unit. I removed and attached the sled to the new unit with 3 screws.
Was this helpful?
Thank you for voting!
Ice maker wouldn't work
3 of 4 people
found this instruction helpful.
-
Rich from Covina, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Ice maker wouldn't eject the ice often enough. After reading a few other stories, I just ordered the universal ice maker from Part Select. All I had to do was remove some of the plastic shrouds from my old ice maker and put them on the new one. I also reused my mounting brackets. The whole job took me 20 minutes.
Was this helpful?
Thank you for voting!
My frost free refrigerator kept freezing up thus not letting any of the air pass through it. It was during the holidays when our refrigerator was bing used at its max.
3 of 4 people
found this instruction helpful.
-
Allan from Sandy, UT
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
I removed all of the cover screws and then had to defrost the coils. Once i had that done I undid the 3 scres holding the coil in place. Took out the old heater part and replaced it. The hardest partof the whole project is trying to avoid getting cut on the coil fins. Put it back together and all has been well.
Was this helpful?
Thank you for voting!
Ice maker quit making ice--had to either be a faulty switch in the ice maker or a faulty water valve. I guessed it was the ice maker switch and ended up being correct.
3 of 4 people
found this instruction helpful.
-
Harvey from Port Tobacco, MD
- Really Easy
- 15 - 30 mins
-
Wrench set
It was exactly as everyone else described--remove old ice maker, unplug, plug in new ice maker, attach new ice maker. 3 screws, 1 plug. My plug was the one on the ice maker not on the refrigerator (ie I used the wiring/plug that was already in the freezer).
Was this helpful?
Thank you for voting!
ice maker quit
3 of 4 people
found this instruction helpful.
-
Tim from Ewing, NJ
- Really Easy
- 15 - 30 mins
-
Socket set
i noticed that no water was getting to the ice maker. rather than messing around with parts, i bought the entire unit. easy to remove old one and install new one. thanks...ice started again in about an hour. unit cost less than a service call!
Was this helpful?
Thank you for voting!
icemaker wasn't making ice
2 of 2 people
found this instruction helpful.
-
JAMIE from HANOVER, PA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we
... Read more
get many more years out of this icemaker.
Read less
Was this helpful?
Thank you for voting!
Ice maker quit, I cross wired the two solenoid valves and determined the valvles were not the problem.
2 of 2 people
found this instruction helpful.
-
michael from naples, FL
- Easy
- Less than 15 mins
-
Nutdriver
Used a nutdriver and removed the lower mount nut, then loosened the the top two nuts and the icemaker lifted off, then unplugged the device and replugged it into the "old" plug(the new ones were not needed) then remounted it. Then it did not fill (as others posted happened right away.) Some poster suggested manually filling the tray so I
... Read more
did it. Later it froze and emptied and refilled and started working normally. Not sure if putting water had anything to do with it or it just took some time. It would be nice if the instructions addressed this issue.
Read less
Was this helpful?
Thank you for voting!
Ice maker stopped making ice
2 of 2 people
found this instruction helpful.
-
Sean from Lancster, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here ... Read more for $65.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here ... Read more for $65.
Read less
Was this helpful?
Thank you for voting!
My Kenmore Ice Maker stopped manufacturing ice
3 of 5 people
found this instruction helpful.
-
Kenneth from Philadelphia, PA
- Really Easy
- Less than 15 mins
-
Nutdriver
The repair was very easy. I ordered the part from Part Seelect and the delivery was very quick.
Opened the box and took out the new ice maker. Emptied the freezer, turned off the power and the water to the Refigerator / Freezer / Iceww Maker. Used a quarter inch nut driver to remove the old ice make. Really easy remove one scre ... Read more w and lewsen two ther screws. unplugged the wiring harness. Took the bale arm off old unit and installed it on the new unit. Check to make sure I had the right wiring harness installed on the ic make which it was. Installed and leveled the new unit. in a little over a hour I had ice. Had to make a few adjustments to the water level setting to make sure all ice cube trays filled up completely.
So easy to do a cave man could do it.
Opened the box and took out the new ice maker. Emptied the freezer, turned off the power and the water to the Refigerator / Freezer / Iceww Maker. Used a quarter inch nut driver to remove the old ice make. Really easy remove one scre ... Read more w and lewsen two ther screws. unplugged the wiring harness. Took the bale arm off old unit and installed it on the new unit. Check to make sure I had the right wiring harness installed on the ic make which it was. Installed and leveled the new unit. in a little over a hour I had ice. Had to make a few adjustments to the water level setting to make sure all ice cube trays filled up completely.
So easy to do a cave man could do it.
Read less
Was this helpful?
Thank you for voting!
Ice maker did not make ice
2 of 2 people
found this instruction helpful.
-
Alfred from CANTERBURY, CT
- Very Easy
- 15 - 30 mins
-
Nutdriver
Ordered new ice maker from this site . Installation was very easy. Was happy to see that many electrical plugs were included. Chose the correct electrical plug and installed in 30 minutes. One note, be patient as it takes a while for ice maker to produce ice. When I heard the sound of ice dropping in the bin, I was very happy. Just in tim
... Read more
e for summer cold drinks. :)
Read less
Was this helpful?
Thank you for voting!
freezing water tube and frozen rotation bar whuch caused water to overflow and freeze inside freezer.
3 of 5 people
found this instruction helpful.
-
Donna from CUMBERLAND, RI
- Really Easy
- 15 - 30 mins
-
Nutdriver
put arm up to stop icemaker from creating new ice cubes. us nut driver to unscrew 3 of the nuts holding icemaker in place do not completely remove the 2 top screws. lift off the screws and unplug from inside wire connection...make sure water tub is removed and frig unplugged. clean off ice anywhere inside freezer...take out new icemake
... Read more
r and connect wire plug...attach icemaker on to the 2 top screws...use nut driver to tighten into place. add and tighten bottom screw...leave arm down...replace clean and dried water tube into back and make sure it slid into ice maker...tighten screws in back and attatch water hose to tube...plug frid back on slide back into place...will start making ice in an hr or so....
Read less
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 people
found this instruction helpful.
-
dorotea from staten island, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
Stopped making ice. Black stuff coming out on ice
2 of 2 people
found this instruction helpful.
-
Paul from Navarre, FL
- Easy
- Less than 15 mins
-
Nutdriver
First I removed the (3) screws holding the unit to the side of freezer wall with a nutdriver. Then I disconnect the Harness from the back of the freezer. You have to work the Harness off connector because it was very tight. The Unit came with the correct harness installed so I reconnected the harness to the Freezer and replaced the (3) sc
... Read more
rews. I had ice in about 2.5 hours.
Read less
Was this helpful?
Thank you for voting!
Unit wasn't producing ice
2 of 2 people
found this instruction helpful.
-
Michael from Ocoee, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
It actually took me longer to think about the repair than actually doing it. It was three screws, two upper that you just loosen and then one on the bottom that you remove. Pulled the unit out and disconnected the power. Slipped the new unit onto the two upper brackets, after connecting the power cord, tightened the bracket screws, reatta
... Read more
ched the bottom set screw and I was making ice. Incredibly easy. When I ordered the replacement unit they said it would arrive in 3-5 days, but it only took a day and a half. Great experience all the way through. I'm a customer for life.
Read less
Was this helpful?
Thank you for voting!
Water starting coming out of the ice maker uncontrolable - ice maker was broken
2 of 2 people
found this instruction helpful.
-
Nicole from Fishkill, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
removed the three screws holding the old ice maker in place - unpluged the electronics .... took the new ice maker pluged in the electronics screwed in into place and we were in business and had ice within an hour.
Was this helpful?
Thank you for voting!