EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

KSSC36FMS02 KitchenAid Refrigerator - Instructions

All Instructions for the KSSC36FMS02
121 - 135 of 575

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Icemaker shaft would not turn
2 of 3 people found this instruction helpful.
  • Richard from Lewistown, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Installed new motor control
Was this helpful?
Thank you for voting!
wasnt making ice
2 of 3 people found this instruction helpful.
  • kandra from newhall, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
followed instructions provided when ordering part
Was this helpful?
Thank you for voting!
motor assembly was shorting out
2 of 3 people found this instruction helpful.
  • Paul from Boring, OR
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I removed the cover to assembly ,3 screws and it came right off. points were wore out. Thank you for a prompt delivery. It was delivered much faster then I expected.

Paul First time dealing with you ,thanks
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 people found this instruction helpful.
  • Gail from Golden, CO
  • Really Easy
  • Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
Replaced water filter on whirlpool gold side by side refridgerator.
2 of 3 people found this instruction helpful.
  • JOHN from PALM COAST, FL
  • Really Easy
  • Less than 15 mins
followed the instruction video,that PartSelect provided on the web site,It was very easy
Was this helpful?
Thank you for voting!
not making ice
2 of 3 people found this instruction helpful.
  • salvatore from wantagh, NY
  • Really Easy
  • Less than 15 mins
  • Wrench set
first i removed 1 screw, then pulled out the ice maker, unpluged the electrical wire, i removed the white plastic cover , then an additional 3 screws . i pulled off the ice maker control . replaced with new ice maker control. i repeated the steps to put back the ice maker ...so
super quick part delivery !!!
Was this helpful?
Thank you for voting!
Ice maker stopped working
2 of 3 people found this instruction helpful.
  • Marinus from Crestone, CO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the control and motor assembly by removing the plastic cover and three screws. Shut off the power to the refrigerator while removing the control and motor assembly (and also when installing the new one). Tested the motor using an AC power cord. The motor had apparently failed. Ordered the repair part and installed it taking ca re that the motor drive shaft and shut off arm were correctly aligned. The icemaker began to work properly when power was restored. The cost of this repair was about half the cost of replacing the entire icemaker.
Was this helpful?
Thank you for voting!
No ice from ice maker
3 of 6 people found this instruction helpful.
  • James from San Diego, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Replaced motor-modl (part #W10190935) by un-screwing 3 screws, disconnected the the electical plug, removed 3 screws that held the motor assembly to the and removed the motor and replaced with new motor but this did not fix the problem and still had no ice. Since frig was 10 years old decided to buy new one as cost to repair would probab ly cost a few hundred dollars. Gave frig to family member as second frig as they already had ice maker.
Was this helpful?
Thank you for voting!
Ice maker quit and Ice dispenser
2 of 3 people found this instruction helpful.
  • jeffrey from fairmont, WV
  • Easy
  • 15 - 30 mins
  • Nutdriver
The ice maker had quit before and I fixed it by taking it out to thaw.When it quit working the second time thawing it out didn't do the trick.The dispenser still worked so we were buying bagged ice. The dispenser lever fell apart and my wife said fix them both or "I'm calling a repairman." My in-laws recently had a bad experience with an appliance repair service and my motto is that "if it's already broke I can't hurt it anymore" Found the Parts Select site and started reading everyone instructions. During the summer,our electricity had went off several times,so I figured that the icemaker control and motor assembly was the problem. Watched the installation video,and followed the instructions. Used parts diagrams and super glue to piece dispenser lever back together. Wife is happy and we saved $
Was this helpful?
Thank you for voting!
Ice maker not working....
7 of 18 people found this instruction helpful.
  • Marie from Homosassa, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Took the front of the ice maker off. Noticed the arm inside was broken, found the part on your site and ordered it.....super fast delivery. Replace the moter assembly and off she went. had ice in about 30 minutes. Thanks for your services and I will highly recommend you to others......Thanks again.
Was this helpful?
Thank you for voting!
Ice maker: The gear on the motor module was broken
2 of 3 people found this instruction helpful.
  • John from Athens, TN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I had to order the module. It was easy to install. If i could have ordered just the gear and shaft, would have been a lot cheaper. Thanks for the addvise. Bill Paisley
Was this helpful?
Thank you for voting!
I never changed the filter
2 of 3 people found this instruction helpful.
  • Christine M from Royal Palm Beach, FL
  • Really Easy
  • Less than 15 mins
  • Pliers
After my son-in-law told me where to change the part, I had to use pliers to turn the knob and it came right out. I replaced the filter turned the knob.
Was this helpful?
Thank you for voting!
timing contact wheel was not making reliable contact
2 of 3 people found this instruction helpful.
  • Robert from Pebble Beach, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Repair was replacing motor kit. I did not use the plastic parts - ejector arm and separator. Went same as others described. I had removed ice maker from refrigerator although this was not necessary to replace motor unit(Please unplug refrigerator whether or not you remove the entire ice maker).
Removed three screws, removed old moto r unit, inserted new unit making sure the ice level wire arm end was in slot. Ejector is D shaped so can't go in wrong. Replaced screws and replaced ice maker in freezer. Note - be sure the water tube is in the trough before trying to refasten ice maker.
Added note: If for whatever reason you need to remove ice maker note that there are three mounting screws (others have mentioned this) Completely remove one under middle of ice maker. For the two at top of ice maker - just loosen a few turns. The ice maker can be lifted and pulled away from the wall without removing these screws. Also there is a tab on the electrical wire connector for ice maker at back wall of freezer. Tab must be depressed with a flat tip screw driver while pulling out to remove wire connector. Tab is on wide side of connector facing inside of freezer.

Repair worked. Have lots of ice again.
Was this helpful?
Thank you for voting!
No Ice, water was valve working, the ice tray was turning
2 of 3 people found this instruction helpful.
  • Jerry from MERRITT IS, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Installed the icemaker control assembly this corrected the problem suspect contacts on the old unit were not making a good contact over time, due to the damp area in the freezer the new unit corrected the repair easy repair.
Was this helpful?
Thank you for voting!
Water liking into the ice tray causing an iceberg
2 of 3 people found this instruction helpful.
  • Joe from Newbury Park, CA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
Removing the ice making assembly from the Ice compartment was not difficult except that two of the 3 screws we not visible without a mirror and then my nut driver was 5" long making it very tight quarters, so it was a time consuming process to remove them.
Once the 3 screws were removed the wiring harness was easily disconnected and the whole assembly came out.
The next step was to figure out how to remove the faulty part from the rest of the assembly.
After some strong persuasion the part would not separate from the control Assy. (The front of the unit) To complete the job I had to pull the front cover and unplug the motor and heater assy to expose two additional screws that had to be removed to pull the defective part out. The reassembly went quite easy except the 2 screws that you need a mirror to see. I was also trying to hurry because the frozen items were not holding all that well after the door was open for about an hour and a half. An instruction sheet showing the steps would have cut the time over 1/2!
Was this helpful?
Thank you for voting!
All Instructions for the KSSC36FMS02
121 - 135 of 575