KSSC36FKB00 KitchenAid Refrigerator - Instructions

Replaced the cap no tools needed

replaced the water filter. very easy, just insert and turn.

First the small screws you sent did not fit.I had to cut and mend the old ones (2) to use them.I did purchase a connecting valve tha I used to connect the part of tubing (my name for it) from old one to new one.I was surprides it is working fine.Not bad for a nurse!

Unpluged the refrigerator, removed the burnt out switch by unpluging it, plugged the new one in re installed the switch into cover. Plugged in refrigerator replaced cover. Done. Easy as one two three

fist turned off water supply. then removed bottom kick plate. unscrewed old valve, unscrewed each water line. removed old valve. put in new valve and repeated putting back each water line than the kick plate. depending on the height of your refrigerator you may have to crank up the leveler bolts to give you more room.

take out Ice maker tray, remove three screws holding the ice maker, unplug electrical connector. Replace with new Ice maker,Ice started to fill the tray. ENJOY!!
THANKS.

The actual repair was very easy, what was the difficult part was to get to the valve!! It is on the bottom front but the size of the valve is larger than the opening so we used PVC pipe to create a fulcrum so that we could pick up the front of the frig about 1/4" to remove the valve. We then did the exchange, tube by tube, and again picke ... Read more d up the front of the frig to replace. Thank goodness we didn't need more than that as it is a built in refrigerator! It would have never been done!!

It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of ... Read more scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.

I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.

ordered the part, pulled out the icemaker unit, removed the module, put the new module in, reinstalled the ice maker unit and let it run.

Removed old loose caps and front plate by sliding caps up or down out of door inserts. Slid new caps in and snapped them into place (note: although caps ordered were for left and right specifically, they were identical when received, so intalled one down side up and the other up side down and they worked fine this way...not sure why they ... Read more were priced differently?). Spread outer end of caps and re-intalled front plate.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Very easy to order from parts select. Took seconds to replace.

Removed ice maker from fridge. Removed motor assembly (3) screws on cover, and (2) screws inside. Removed mold (3 screws on bottom) and replaced everything in reverse order. Note: Turned ice maker off for several days while waiting for parts. The water line on this particular model will freeze inside the freezer if ice isn't made for ... Read more several hours/days. You will have to defrost to begin making ice again.

With instructions from PartSelect.com this was an easy fix. I tested the motor's electric as suggested and was satisfied that the Motor Module (WPL W10190935) would correct the problem. UNPLUG THE REFRIGERATOR! I popped the outside plastic cover off to expose the unit. (1) remove the wire unit that runs the length of the cube maker (2) re ... Read more move the 3 screws that secure the motor unit and carefully remove it (3) carefully line up the new unit, slide in place and replace the 3 screws (4) install the wire that was removed in step(1). Connect electric to the refrigerator and wait about 2 hours for your first ice cubes. PartSelect.com is the ONLY supplier that you will ever need! Great instructions and trouble shooting suggestions. Shipping is incredibly fasssst! Customer contact is awesome. Don't hesitate to buy from them! Saved me about $200.! Good luck....Tom in SC