KSM90 KitchenAid Mixer - Instructions

Skewer the screw in with my fingers,

I removed three screws, pulled off the old base plate.
Put new base plate in place and replaced the screws

I removed one screw on back, once inside mixer I removed the ground screw then pulled off the black and white push on caps, then I reversed everything to get it installed, very easy

Just put on the new whip...exactly like old one.

Fairly easy if you have done it once before.

watched an internet video to see what to do. Unfortunately even after replacing the chip the mixer it still didn't work.

Order the worm gear part number PS11748374.
Watch this video.
https://www.youtube.com/watch?v=VeCiivPt7hk

I would recommend two people if possible.

i disassembled the mixer until i could remove the worm gear; is in a housing that that includes another gear and shaft. make sure you have a magnetic tray to put parts in as you work or you will spend more time looking for parts than reassembling the mixer. once you have the gear housing out you will need a small diameter punch to drive ... Read more out the pin that holds the gears in the housing(i used a 5/32 transfer punch.) make sure you punch the pin out where it will be caught or you will need to order that part because you will not find it. after knocking the pin out it is just a matter of removing the old gear, putting the new one in, and reversing the steps and getting everything reassembled.

Replaced the speed control plate and phase control board and works well. Pay attention to speed control board spring and adjustment lever when reassembling.

I followed the instructional video linked to my email order confirmation. Partselect provided one of the best how-to videos I've ever seen. With the right tools, a little patience and the video, I had an outstanding repair experience.

Rather than duplicate previous repair works, I recommend going to this user site and follow their instructions: http://www.neilcrockett.com/mixer1.htm. Once you have done this repair, taking the unit apart is easier to perform this tasks. Order replacement Grease "Benalene 930-2" in the 3.3 oz container and be sure to use the full cont ... Read more ainer to lather all around all the gear components so grease will be available to units for years to come due to heat build up under load. Too, the 3.5 oz container is made for one unit repair job and is available through Amazon. This grease is available on larger quantities if needed / desired. I did order both, a Worm Gear and the Worm Gear and Bracket as I wasn't sure of my mechanical ability to make this repair until I got inside the unit but the worm gear is easily replaced once you clean out all the old grease. The worm gear is a neoprene type gear with all other gears being metal. I assume neoprene is used as sacrificial to save other gears from breaking under loads and years of use.

Follow a YouTube video step by step

1. Removed the mixer back plate Cover. 2. Removed the Speed Control Plate and retained spring, wires and ground wire. 3. Removed the old Speed Control Plate screws. Noted Control Plate pitted contact. 4. Removed old Triac Phase Control Board. 5. Removed old Governor. 6. Installed new Governor. 7. Installed new Phase Control Board ... Read more . 8. Installed new Speed Control Plate and retaining spring. 9. Reattached Speed Control Plate wires. 10. Adjusted Speed Control Plate Screws and set mixer speeds from Stir to maximum settings. 11. Replaced Motor Brushes on left and right side of mixer. 12. Reinstalled mixer back plate cover.

disassembled replaced part reassembled now works well

I did some research and evaluated a modern day Kitchen Aid Mixer. Looked a the wire diagram and found out what items I needed. Ordered them from Partselect. Overall Mixer is updated and running. I made up some cookie dough with it. The Project took a few evenings due to rewiring the coils on the motor/armature and modifying the rear be ... Read more aring bracket to hold the Phase control board (not OEM on 70's mixers). Then put it back together and adjusted the speed control.