My Orders
KSM150Q KitchenAid Mixer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The speed linkage was broken inside the mixer.
3 of 3 people
found this instruction helpful.
Literally the whole top of this stand mixer had to be taken apart. With the help of U-tube! We realized the silver strip was removable and there where screws underneath. We figured we would replace both parts while it was all taken apart. We cleaned the mixer and added some grease where necessary. I now have a 25 year old new mixer. Thank
... Read more
s for having our parts and guiding us with a diagram of the unit. Very helpful.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Mixer would not turn on
3 of 3 people
found this instruction helpful.
Pulled off end cover. Used the how-to video's to show me how to remove the (3) components (watch out when it comes to removing the spring). Removed all (3) components (one issue was the black cardboard seal, which because of its age broke. Hindsight tells me that I should have purchased a replacement seal along with the (3) new parts.
... Read more
r /> Fixed the broken part of the seal with scotch tape). Installed all new parts with the help of the video's and put the cover back on. Even with the new parts, the mixer would not run. Come to find out, after I took it to an appliance repair person, that someone had pulled both brushes and put them back in improperly. I could not find a how-to video that showed me how to de-install/re-install the brushes properly. I assume that was because new brushes were no longer available for purchase. At any rate, when the brushes were put in properly, everything worked. The repair person also adjusted the (2) screws on the speed control plate so that when you change the speeds via the lever, it all works properly. I didn't find a how-to video covering those adjustments either.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Kitchen Aid Mixer won't spin
2 of 2 people
found this instruction helpful.
Order the worm gear part number PS11748374.
Watch this video.
https://www.youtube.com/watch?v=VeCiivPt7hk
I would recommend two people if possible.
Watch this video.
https://www.youtube.com/watch?v=VeCiivPt7hk
I would recommend two people if possible.
Other Parts Used:
Was this helpful?
Thank you for voting!
Speed control not working properly
2 of 2 people
found this instruction helpful.
Replaced the speed control plate and phase control board and works well. Pay attention to speed control board spring and adjustment lever when reassembling.
Other Parts Used:
Was this helpful?
Thank you for voting!
Mixer would slip gears under load, finally would not mix under any load
2 of 2 people
found this instruction helpful.
Rather than duplicate previous repair works, I recommend going to this user site and follow their instructions: http://www.neilcrockett.com/mixer1.htm. Once you have done this repair, taking the unit apart is easier to perform this tasks. Order replacement Grease "Benalene 930-2" in the 3.3 oz container and be sure to use the full cont
... Read more
ainer to lather all around all the gear components so grease will be available to units for years to come due to heat build up under load. Too, the 3.5 oz container is made for one unit repair job and is available through Amazon. This grease is available on larger quantities if needed / desired. I did order both, a Worm Gear and the Worm Gear and Bracket as I wasn't sure of my mechanical ability to make this repair until I got inside the unit but the worm gear is easily replaced once you clean out all the old grease. The worm gear is a neoprene type gear with all other gears being metal. I assume neoprene is used as sacrificial to save other gears from breaking under loads and years of use.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!