Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
mice had made nests in the insulation wrap in the range
128 of 209 peoplefound this instruction helpful.
Wendy from Red Hook, NY
Easy
More than 2 hours
Screw drivers
I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to
... Read more fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.
Read less
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 227 peoplefound this instruction helpful.
Michelle from Richardson, TX
Really Easy
Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Baked on sauce
12 of 16 peoplefound this instruction helpful.
Julie from Newnan, GA
A Bit Difficult
More than 2 hours
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.
Was this helpful?
Thank you for voting!
Oven temperature was WAY off, sometimes 50 degrees.
12 of 16 peoplefound this instruction helpful.
Sarah from Raleigh, NC
Really Easy
15 - 30 mins
Screw drivers
Turned the breaker off. Removed the racks, pulled the oven out and removed the back. Disconnected and unscrewed the old sensor from the back, connected and screwed in the new one. Returned the racks and slid the oven back in.
The only remotely challenging part was disconnecting the old sensor. I had to figure out where to pres
... Read mores with the flat screwdriver to get it to release.
I had found a good YouTube video and didn't use the app.
Remove bottom plate take screws and hex head nuts remove wire unscrew ingnitor reverse process with new ignitor very easy
Was this helpful?
Thank you for voting!
the old gaskt was not linge dup well, the door was not closing well
6 of 12 peoplefound this instruction helpful.
mohaemd from pittsburgh, PA
Really Easy
Less than 15 mins
Screw drivers
pulled the old gasket, the new one fitted perfectly. No effort at all. An instruction sheet would be a bonus. I wish you put instruction sheet in all parts OR a web link for video instructions. a web link would be great
Was this helpful?
Thank you for voting!
FE80 Error, blower motor underperforming
3 of 3 peoplefound this instruction helpful.
Richard from EUGENE, OR
Really Easy
1- 2 hours
Screw drivers
Remove cover under controls, unscrew rangetop (front only). Motor on right side of oven directly under rangetop detaches with 3 screws and remove with care. Swap foam seal to new motor and install. May require contact cement to attach seal to new part.
Was this helpful?
Thank you for voting!
No problems encountered
3 of 4 peoplefound this instruction helpful.
Scott from Troy, IL
Very Easy
Less than 15 mins
It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole. TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or t
... Read morehe point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.
Read less
Was this helpful?
Thank you for voting!
Ignoter gave out
2 of 3 peoplefound this instruction helpful.
Michael from CHICAGO, IL
Really Easy
15 - 30 mins
Screw drivers
Opened oven... removed grates and bottom panel. Unbolted igniter has flange and end wire. Attached end wire to new igniter and reattached new igniter to gas flange. The rest in reverse and set oven and pressed start.
Was this helpful?
Thank you for voting!
Glass on oven door broke
2 of 4 peoplefound this instruction helpful.
Robert from EAST SANDWICH, MA
Really Easy
30 - 60 mins
Screw drivers
Toke the oven door off disassembly door and replaced outer panel and glass
I watched then followed the video. I could not remove the top, so I used a can from the cabinet to support and hold the top. That gave me enough room to get the old fan out and the new fan in. Thank you PartsSelect.
Was this helpful?
Thank you for voting!
door of oven came apart when plastic screw holders broke
1 of 2 peoplefound this instruction helpful.
patricia from chipely, FL
Really Easy
15 - 30 mins
Screw drivers
put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!
My Orders
