KSEG950ESS3 KitchenAid Range - Instructions

Opened the breaker for the oven. Verified the power was off. Removed the racks from the oven. Using a screw driver removed two screws in the back of the oven holding down the steam bake bottom of the oven, pulled up from the back to get the pan out. Removed the screw holding the front of the element in place. Removed the screw in the shin ... Read more y metal of the element at the back. Gingerly pulled the element to the front and as the element stopped slightly turned the element to let the prints come out. That part was challenging to get the angle right so not to damage the wires. Using a small Phillips screw driver I pushed in on the connector latch on the terminal and then pulled the terminals off the element one at a time. Follow all the steps in reverse to install the new one.

Shut beaker off
Unhooked wires on element back of stove
Removed all racks
Unscrewed lower plate cover
Removed element
Inserted new element
Rebooked wires to element
Reinstalled cover plate
Turned breaker back on
Turned range on and let heat up
Turned it off
Reinstalled racks

I purchased cleaning supplies for my new range!

Unplug the appliance, remove the bottom cover inside the range and the cover in the rear to unplug the heating element. R&r the element, reinstall the covers and test for proper operation.

Lifted the range burner top removed the old element and installed new burner unit .

Took off top and pulled out old element and plugged in the new one

Took out the bottom tray and the back cover panel, unplugged the old element and plugged the new one in and reassembled

I slid the range out only a couple of inches so I didn't have to detach the downdraft blower connection. Undoing the four #2 square head screws was easy from the under the control panel as well as the three pairs of screws holding the front of the glass cooktop frame. Undoing the two in the rear (one on each side) was a bit of a challeng ... Read more e in that they were in upside down and difficult to see without a mirror. It was easy to drop the screws as they fell never to be seen again. After they were removed the top was easily removed. Reinstalling the back two screws was the most difficult of the entire procedure. I replaced the #2 square head bits with the same size hex head screws. Using a nut driver made the whole process much easier. By the way, the distance between the holes in the rear and the replacement top is 1/8" difference that made lining up the holes a frustrating experience. I ended up using a rattail file to hog out the opening to enlarge the holes. That made the lineup much much more easy.

1) unplugged rnage from wall
2) took off back plate to unhook electrical from element
3)took door off of range for ease of access
4) removed the 2 screws i the back of tha bottom panel
5) removed 1 screw in front and 1 screw in back to be able to remove old element.
6)remove element and replace with new one.
... Read more 7) reinstalled both screws and the bottom panle.
8) connected electrical to new element
9) replaced back cover and plugged in unit to wall
10) put range back in place.

I read the help section and it said that the element was likely to be the problem (84%) and the fuse had a 14% chance to be the problem so I purchased both. After watching the video I tried the element first and that's what it was so I returned the fuse, Thanks for the help and video.

The company said it would cost me $698 to r ... Read more epair. I had a 2 year warranty and that was 2 months out of date.

Again thanks for the help.

I pulled the range out from the wall, then unplugged it from the wall outlet. I removed the oven door & set it aside. Removed the screws covering the rear wiring shield, then disconnected the 2 leads from the bake element. Unscrewed the screws holding the oven floor pan, then unscrewed the screws holding in the original element. Replaced ... Read more it, screwed everything back together, and pushed the oven back against the wall. Took me about 30 minutes, and now the oven works as well as it did when we first bought it.

The You Tube video for replacing the Element was very useful. Let me know exactly how to proceed - it was easy.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Repair has not been made yet still waiting for the part. The part is on order and was told it would be shipped in 1/3 business days. Still waiting for the part to come from China. This is the problem with parts being made out side the U. S. A.

pulled the old gasket, the new one fitted perfectly. No effort at all.
An instruction sheet would be a bonus. I wish you put instruction sheet in all parts OR a web link for video instructions. a web link would be great