KSB5-3 KitchenAid Blender - Instructions

Because the old coupling was so tightly screwed onto the shaft it was necessary to use very flat wire crimpers to slide between the old coupling and the blender housing to grip the shaft and immobilize it while pliers were used to grasp the old coupling and loosen it---rotate clockwise.

Used a wrench 19/64 flat

Pried the old coupling off and unscrewed the metal piece remaining then screwed the new coupling on.

My husband lifted off the old piece with some difficulty and then just screwed it back on. We were really glad to have our blended back as good as new for under 20$!

The repair is easy. Just follow the directions that come with the replacement part. And parts select is awesome. I received the parts within a couple of days and fixed it right away.

I will definitely use this company again. The blender was over $120 when I brought it and I did not want to spend that kind of money again. My co ... Read more st to fix was about $8.00 for the part and $7.00 for shipping. Hmmmm, $15 vs. $120+ sounds like a good deal to me.
Thank you.

Went easy

Last time this happened we simply used a thin wrench to unscrew the damaged coupling. This time it was so tight no wrench could undo it. We had to grind it off using a grinder drill until it was so loose it popped off.

Simply to find the look of dismay in her face. After I violently began shaking and dismantling the compactor in disgust. I decided to unplug it from the wall, I then gathered my senses and began to perform a electrical diagnosis and found that the rotary swich contacts, which activates the compactor, had gone bad. I simply went to the w ... Read more ebsite and selected my part # from the detailed spec sheet. I chose to receive the package on a three day shipment. Here it arrived, installed the part and away the problem went. While on the parts list I included bag brackets that had broke over time and now my compactor is like new.

Following the instructions which was quite clear.

Simply followed the online video instructions. Screwdriver to remove the worn out part. Rag to clean threads. Hand tighten replacement part (reverse threads). Blender fully functional. Couldn't have been easier.

place screwdriver under old coupler and pried up on it in different spots until it popped off. Took less than 5 min. to do.

Part is left hand thread. Use screwdriver to lock motor fins and twist off part.

I followed the instructions on the sheet that came with the replacement part. The instructions are accurate, however, the working is misleading. I think additional information is needed to make the install easier. First, a flat head screwdriver works best. Also, all the rubber that is on the broken coupling needs to be removed before tryi ... Read more ng to get the coupling off. Once all the rubber has been removed then it becomes easier to see the metal rod that holds the coupling and distance between the coupling and the base of the blender, take the screwdriver and gently pry the coupling off in an upward movement while going around in a circular manner. Then you can see the coupling rising up from the rod. Then take a hold of the broken coupling and pull it off. Then attach the new coupling, screwing it on counterclockwise. Once you realize what is going on, it's actually quite easy.

simply hold the axel with the wire stripper to prevent from rotating. Using the pliers firmly turn old coupling counterclockwise until loose. Once this coupling is totally off you are ready to screw on the new one. Very simple. The most difficult part was finding a tool slim enough to fit between old coupling and base to hold axel fro ... Read more m spinning. I ordered part on sunday and received it on tuesday. It spared me from throwing away a $120.00 dollar kitchenaide blender.

I inserted a metal rod in the bottom of the base while I held it sideways to keep the motor from turning and I used pliers to twist the coupling off counterclockwise.
I thought at first I was doing it wrong because it wouldn't nudge so I left it alone. I then read the repair stories again and went back to it and it right came of ... Read more f. I guess there was a lot of gunk holding it tight.
Of course when the new one came days later it was easy to twist it on. Thank you for all of your stories. They were very informative and encouraging. Without them I'm not sure if I would have attempted it myself.