KSB3-4 KitchenAid Blender - Instructions

Inserted the screwdriver under the original gear and pried it off. After that you just screw the new gear on, it has reverse threads so no tighting is required.

I used a screwdriver,pulled out the piece,then change with a new one,that I was ordered before.It was ver easy to assembly.

followed instruction, prying off old coupling and screwed new coupling on less than 5 minutes. Parts came in a timely manner. great service, satisfied customer

popped off the old one, popped on the new one. could not have been any easier. :)

Followed the video you sent removing the old drive coupling. Installed the new part according to instructions. I found I did not need to order the seal. I am a do it yourselfer and have never had such a good experience.

Very easy. Enclosed instructions were excellent! Part arrived early than anticipated, also.

Just took a screwdriver and pried off the broken coupling as the instruction said with the part. Don't stress it really works and is easy. Ordered the part on Monday and recieved it on Tuesday. Great service from Partselect!

Remove blender jar to get to drive cog. Use a 1/4 to 3/8 flat open-end wrench to hold cog shaft then turn the cog with your hand CLOCKWISE to loosen. Screw new cog gear on COUNTERCLOCKWISE hand tight. Reassemble your blender and you're good to go. It takes a very thin flat wrench but even if you have to buy a set the're not very expensive ... Read more . Good luck.

A very flat wrench or needle nose pliers was needed. I could not get the nut unscrewed with what I had so I had to mail the unit to a service center for repair. They were able to use the part I had purchased but if I had known I wouldn't be able to do it I could have saved a little money in the shipping I had to pay when I ordered the p ... Read more art.

Thanks to the good advise of those who did this before me ,I know I need a very slender wrench to get between the screwed on base of the coupling and the copy of the base of the blender.
I tried to file one myself, but the metal was too weak. Because i had the size (from what I filed), I measured and knew i needed a 7 MM wrench. I bo ... Read more ught one at the parts store and ground it thin enough to slip into the small space and from there it was a five minute job.

Directions included with replacement part were no help...maybe I'm stupid, but prying up on a threaded metal part didn't help unthread it at all.
Vise grips solved the problem. I used vise grips to remove the rubber from the coupler while it was still attached to the blender base, exposing the metal base to the coupler. (yes, I used ... Read more vise grips to destroy the damaged coupler. after all the hell I went through to try to do it as the directions said, it was very satisfying.)
After removing the rubber, I used the vise grips to bend and distort the metal base until I could get a pair of needle-nose pliers around the drive shaft and hold it still while I unscrewed the now bent-up metal base. Victory!
I thoroughly recommend this method to anyone else, as using vise grips to destroy something is very gratifying.

Read provided instructions but unfortunately looked at part and re-interpeted the instructions....Should have just followed instructions as printed. I tried to pry up and unscrew instead f just prying off...

Followed instruction sheet, but as it stated just remove by hand, not so, had to grind open end wrench to fit between coupler and base to fit flat sides of shaft, then use channel locks to break lose and to unscrew most of the way off.
But in the end the part worked just fine.

Tried to follow the included instructions - no way that just prying the coupler off would work without bending the shaft and wrecking the threads! Then used a flat, open-ended 7mm wrench to hold the shaft and pliers to remove the coupling. The coupler was so tight that I could not unscrew it without the wrench slipping. Ended up shoving a ... Read more screwdriver through the fanblade from the bottom (unplug it first!) and use the pliers to unscrew the coupler (remember, it's a left handed thread!)

it need a special tool...to remove the broken coupleing..had to have my brother-in-law who fixes industrial equipment, remove it with a special tool, that a home owner would not have