KRSC Refrigerator - Instructions

Removed some frozen items to gain access to light in ceiling. Small flat screw driver to push in tab to release fixture being careful not to break anything.

Popped out the old switch and replaced it with the one dying

The part was perfect, easy installing. The customer service representative was knowledgeable and very helpful.

took shelf out of box and put the shelf in the freezer

Remove drawer and install new drawer.

Just plugged it in

Took the old one out and put the new one in

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?

Disconnect power. Tape the front of the door around the control panel to prevent scratching. Use the putty knifes to pry the panel loose from the bottom and sides at the lower corner. Once the panel is loose, unplug the wire connections that are attached. Use a 1/4” nut driver to remove the screws that hold old ice door assembly in. R ... Read more eplace with the new assembly. Reconnect the control panel connectors. Remove the tape from the door, snap the control panel back in by inserting the top of the panel first, then press the sides and bottom in place. Restore power and you’re done! Easy peasy.

Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.

We thought the trim piece would pop off the drawer, but instead the trim is glued to the drawer handle. After puzzling over what to do for a couple minutes, we grabbed some pliers and SLOWLY leveraged / peeled the old trim off and put the new trim on.

Go slow. Bend the old trim as you peel it off and use the pliers as a lever. ... Read more Do a little at a time.

Following a you tube video, I followed the instructions. However, the old switch did not come out as easy as the video showed. They showed inserting the putty knife at the bottom of the switch to pop out the switch. However, in my refrigerator, the flex tab was at the top. After I inserted the putty knife at the top of the switch it c ... Read more ame out easily. I removed the broken switch and inserted the new switch with no further issues.

I took off the broken tube and attempted to order a new one with the confusing we sight at parts.com- after 3 attempts I finally got the right part with help from the operator at parts . Com( nice and helpful) but had to ship wrong parts ( the 2 wrong ones) back. The parts were of good quality and we're not hard to put on

Remove the ice bucket and check that the auger that turns in the ice bucket is free to turn. Cover the open freezer with cardboard or whatever to retain most of the freezer temperature. Remove the holder that supports the top of the motor shaft. Check the splines on the upper part of the motor shaft and also check the seal under the holde ... Read more r. Open the access the door to the motor, remove wiring connector and unbolt the motor. Check the lower splines on motor shaft for condition, clean the shaft and apply new grease to the splines. Before installing, connect the wiring to the new motor, push the door switch in, press the ice dispenser arm outside the door to make sure the motor runs. If all ok, check the motor shaft for fit in the new motor. Be careful not to install the motor shaft too deep in the motor splines, otherwise there may not be enough spline showing on the top end to engage the auger. Bolt the motor in place, close access door and install the holder and ice bucket and make sure everything works. If there is not enough spline showing thru the holder to engage the auger, take pliers and pull the shaft up a bit. This seems to be a hit or miss fit on the shaft but you can adjust the height of the shaft without taking every thing apart again. That's all, not difficult at all. But do check parts and pieces for anything else you might need, parts wise, before ordering the motor by itself like I did. Shipping is high, so try to order any associated parts needed when you order the motor. By the way, This site are great to work with!