- Home
- KRQC736RPS00
- Instructions
KRQC736RPS00 Whirlpool Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice dispenser motor burnt out, water got inside.
86 of 129 people
found this instruction helpful.
-
Blye from Victoria, VA
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Purchased new motor from Partselect.com. When it arrived it came with a new rubber washer that fitted on top of new motor that was not on old motor, that how water got into old motor. However, the instruction sheet did not give info on how to access the proper way to the motor that is the door. Not wanting to damage the freezer door assy.
... Read more
called in a tech who made it look easy, but even he had a little problem locating access panel that was directly under the motor in the freezer side of the door. After that it was a piece of cake.
Read less
Was this helpful?
Thank you for voting!
Ice Augur Motor not Working
4 of 5 people
found this instruction helpful.
-
Mark from WISC RAPIDS, WI
- Really Easy
- 30 - 60 mins
-
Nutdriver
Very easy doit repair. Watched Youtube video helpful. Small nut driver and flashlight the only tools needed. Ordered part with standard delivery and received the new motor in under 24 hours! Impressive. I will use Part Select again! So happy to have a working augur. No more stale ice at the bottom of the bin. No more scooping ice
... Read more
with fingers!
Read less
Was this helpful?
Thank you for voting!
Ice make auger stopped working
3 of 4 people
found this instruction helpful.
-
John from WADING RIVER, NY
- Difficult
- 30 - 60 mins
I carefully matched the model number to replacement part cross-reference and ordered the Part.
You-tube instructions were accurate except for the plug wire that prevented removal of the auger motor. It took significant maneuvering to drop the old motor. The new motor fit in better but the male plug configuration did not match the f ... Read more emale plug from the refrigerator.
A lot of wasted effort and time as well as expense! What good is matching replacement parts when the replacement is not correct?
You-tube instructions were accurate except for the plug wire that prevented removal of the auger motor. It took significant maneuvering to drop the old motor. The new motor fit in better but the male plug configuration did not match the f ... Read more emale plug from the refrigerator.
A lot of wasted effort and time as well as expense! What good is matching replacement parts when the replacement is not correct?
Read less
Was this helpful?
Thank you for voting!
Agitator seized because of rust
2 of 3 people
found this instruction helpful.
-
Robert from FORT MYERS, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Replaced motor
Was this helpful?
Thank you for voting!
Motor stopped working
2 of 3 people
found this instruction helpful.
-
Jason from Roanoke, VA
- Easy
- 15 - 30 mins
-
Socket set
I thought this was going to be much more difficult than it was. Take the bottom access door off (using a small socket - same size for all screws). Disconnect the plug to the motor. Unscrew the 4 screws holding the motor. Take the motor out. Unscrew the shaft screws on top (only 2) so you can manipulate it if need be up and down or sp
... Read more
in it. Insert new motor and make sure shaft is seated correctly into the motor head. Screw motor back in. Screw shaft back in. Plug up motor. Screw bottom door back on. You are done. EASY!! Took me about 10-15 minutes to do. Much easier than most things.
Read less
Was this helpful?
Thank you for voting!