KP26M9 Mixer - Instructions

I replaced the switch component twice and I still have the same problem. I will purchase a new motor now see if that works? I'll post what happens thanks

Remove screw and nut from back of mixer head to release the silver name band. Remove the exposed four cross head screws, (two each side), and lift off the motor and gear cover. Wipe excess grease from gear wheels to expose the retaining ring clip at top of vertical gear shaft. Using small nose circlip pliers, remove retaining ring and b ... Read more evel gear wheel to expose shaft pin and worm gear. Support the shaft from below and remove pin. Lift off worn worm gear wheel allowing shaft to drop down. The horizontal worm gear shaft can now be lifted out taking care to keep assembled. Carefully clean old grease from all gears and from the gear housing, (note that broken pieces of the old worm gear are in the old grease. Repack housing with fresh high performance grease recommended for worm drives. Cover new and reuseable gears with grease. Reverse the process to reassemble the unit.

Looked at the schematic for this model on Parts Select. Removed Aluminum band screw, removed the 4 screws that hold the top of the mixer. Lifted the top off. Removed 4 screws and lifted the gear case. Removed snap ring and took off tapered gear. Removed pin and removed worm gear. Picked out the metal, in the grease, from the old worm gea ... Read more r, using a magnet then inserted new worm gear and put it back together in reverse order. There was plenty of grease and didn't need to add any.

I have to thank you at Partselect.com. You happen to help me help other people. Now I have several people bringing me their Kitchenaids to me instead of sending them in. I replaced two worm gears on a Kitchenaid 6 and the Hall sensor on a Kitchenaid 5. Very easy to do. Next week I have another Kitchenaid 5 to replace the motor on. ... Read more Thankyou again for having the parts I need

Took housing off, removed computer board and disconnected speed control assembly from board. Soaked plastic slide in hot water and freed up mech. Discovered a crack in plastic slide from forcing it. Ordered new assembly and installed. TIP: Keep slide clean of substances that will jam it by cleaning occasionally with water. For a complete ... Read more cleaning you will have to remove it. Total of 6 easy to reach screws.

Following Replacement Part Youtube instructions, I disassembled the mixer and found what caused the sounds and prevented the mixer from operating. The worm follower gear had been ground down by the worm gear. I found that the shaft from the planetary gear had not been adequately greased and siezed preventing the worm follower gear from t ... Read more urning. The worm gear is obviously made of harder material and thus, was able to wear away the follower. I appreciate the your help which saved having to replace a perfectly good/expensive mixer. Thanks.

Easy repair that replaced the variable speed switch. The broken switch only ran at high speed. To replace the mixer would cost at least $500. The new switch was $45 and was an easy install. I marked the four electrical leads with a Sharpie and loosened the two screws holding the switch. The repair was super easy. It was like heling an old ... Read more friend recover from an illness.

We are a pretty handy bunch here. However, the diagrams provided with the part numbers did assist in the disassembly. It went smooth and easy.

Removing the cover of the mixers "guts", it was immediate evident the a major gear had lost a few of its "teeth". Parts Select clearly offered the required part of this $300 mixer for a favorable price. I was fully impressed that it arrived within 4 days or my ordering the part. I simply exchanged the damaged gear and restored the mixe ... Read more r to service and I'm fully impressed with the Parts Select Company for their swift response to my needs.

opened the mixer.. all screws in kitchaid are the same so not to worry... opened up and replaced the gears... and put it back together... diagram helped in that front and rear bearings of connecting gear are the same # on diagram it is easy to confuse when you put it back together, but the item number and description of each helped make s ... Read more ure it was in the right place. Otherwise... time to fix would have been less....

took mixer cover off, took gear box cover off, removed gears, replaced gears, replaced covers, made cookies, no problem!!

replaced Speed control board. less than 40.00 took ten minuets from the time I started until we were making cookies.

Open the package with the new screw and it looked like the screw was wider. I tried it to see if it goes in and as long as you screw it straight in, there was no problem.

I sent for a new thumb screw and screwed it in where it belongs and now I can use my other attachments.

Removed one screw to remove deco band around mixer body. Removed four screws under band to remove mixer top. Removed two screws holding switch. Removed wires one at a time putting them in the same position on the new switch. Re-attached switch, mixer top, and deco band. Works perfectly.