KP267 KitchenAid Mixer - Instructions

Took it apart, found stripped gears, a common problem. Reviewed parts diagram on your website. Got the parts, reviewed the diagram, removed defective parts, used retaining ring pliers. put it back together, put new grease in, tried it out. Very easy fix

Unplugged unit. Took top housing off of mixer (half dozen small screws). Disconnected speed control circuit card from five wiring connections. Removed card from mixer chassis (two screws). When new part came (the next day) I reversed the procedure in about 5 minutes and had a working mixer! Thanks.

unscrewed the old one........screwed in the new one, no chance for electrocution or power tools..........darn!

This is the tightening screw that holds the attachments into the motor unit of the mixer. Found your web site and reordered 2 replacement pieces (in case one breaks!). Very EZ and user friendly. Thank you!

This was easy once Igot all the parts. The mxer wouldn't mix and when I opened it up the drive gear between the motor and the planetary drive was missing some teeth. Turns out the bearing, which was sintered bronze, had broken so I needed a new gear, new bearing, and the jumping gear had broken the housing so I needed a new housing. Th ... Read more e new gearing ( really a bushing since there are no rollers or balls in the "bearing") waws now steel and the molded plastic housing is now cast metal. Some new grease ( I had to buy a quart can of grease to get two tablespooons) a new gasket and put the screws in and we're back in business. Total repair time 10 minutes, total time to get all the parts 3 weeks,

removed cover annd snap ring removed gear and replaced with new,

Removed 4 screws on mixer top. Removed 4 screws to gear box cover. Ordered replacement gears from Parts Select. Removed snap ring. Repaced two gears. Applied gear grease, replaced snap ring & screws. Gears at local appliance dealer were $39 each. Total parts from Parts Select + shipping under $20, received in 3 days!

Watched several videos on repair. Noted part placement while disassembling. Found problem, ordered and received parts. Cleaned out all old grease. Greased all parts and reassembled per recommendations, paying attention to the bearing race and washer placement. Firmly tensioned all fasteners, cleaned up and tested.

Remove top of mixer and remove gear housing. Remove old grease and clean gears. Place new grease and install new housing. Replace top of mixer.

Removed top cover of mixer which was very easy. Then marked the 4 wires so they could be plugged back to new switch correctly. Removed 2 attaching screws to remove switch and one squeeze connector. Installed new switch after plugging on 4 wires. Snapped squeeze connector in place. Reinstalled top cover.

3d time in 20 years, but the mixer itself is built like they did 20 yrs ago PartSelect had the part in my mail box in *20 hours* from online order!
See https://www.ereplacementparts.com/kitchenaid-4kp26m1xmc4-professional-stand-mixer-parts-c-114958_114959_115101.html for instructions.
BUT - they changed the design so a power s ... Read more witch previously separate from (to the left of) the circuit board is now a microswitch integrated on the board, leaving you with ONE LESS WIRE.
Attached is the fix diagram & directions for the new design.

Removed screws holding top, then removed the switch retaining screws. Removed and replaced switch wires and re assembled cover.

Researched the internet for a diagram of the mixer and used that to take it apart, clean everything, then install the new gear and new grease. Works great so far.

Took the mixer apart many times. Grease all over the place. put new gears in still noisy. The worm gear must have been cut wrong. The noise still there. The part select sent out a new worm gear. I did not put it in yet. I put the old worm gear in and the noise stopped even though it shows wear. Have not decided whether I will put it in y ... Read more et.I would also like to add that the people that I talked to at the this site were very very helpful and great just great---------

Replaced the worm gears. Original were ground down as if they were not seated correctly. Ordered the parts and swapped them out. I do not own a retaining clip removal tool. This was the most difficult, trying to open the clip using 2 needle nose pliers. It made the repair time longer.