KOSE507 - Instructions

USE 2 PEOPLE FOR SAFETY! SWITCH OFF OVEN POWER BREAKER!! Remove screws attaching oven to wall opening, slide out entire oven just far enough to get to 2 screws on either side of controls, remove those screws (may need stubby screwdriver), lift control front, opens forward, have 2nd person hold control panel cover while removing centered ... Read more thermal fuse (plugs on both ends, may need needle-nose pliers to grip plug on fuse.) Remove old fuse, plug in new one. Close control panel, replace side screws, TEST POWER BEFORE pushing oven back into wall, replace wall-holding screws. Less than 30 minutes. EXTRA PERSON MAKES EASY!

Not a repair. Just needed to replace the meat probe sensor for the programmable oven. Quick and easy purchase and very fast delivery took care of the problem. I was back in business.

Thanks to PartSelect they suggested to try a new thermal fuse first. They also gave a brief description of how to install it. There advice was right on. Replaced the fuse in about 20 minutes from throwing the breaker to turning it back on.

Instructions: Turn off breaker. Remove oven door. Remove screws holding it to cabin ... Read more et. Remove racks. Slide oven out about four inches. Remove four screws holding control panel. Remove thermal fuse. Replace thermal fuse and put it back together.

Thank you PartSelect. Thermal fuse cost me about $28.00 with shipping. This repair would have cost a couple of hundred if I had to call a repair technician.

Remove the oven door. Remove 3 self tappers on rear wall of oven to take off a round access panel. Pull out a pre-cut rectangle of insulation. Next I removed the 2 screws holding the sensor in place. Pulling the sensor out a bit told me I was "touching" the correct wires in the SMALL rectangular opening. The wires are not visable and 2 h ... Read more ands do not fit in this small opening.I looked at the NEW sensor to see the release on the sensor plug. Slip the angled needle nose into the opening and grasp the plug/release side. The plug pulled apart easily. The sensor wire pulls out with a little bit of twisting to fit it out the hole. The new plug pushes in and has to be worked down to where you can reach it. The same angled plier works to re-attach it. It takes longer to read this than to do the job. Best of luck, Al

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Pull the end of the lens nearest the oven door out of the oven wall. Because our oven is several years old and the bulbs had not been previously changed, I could not pull the lens out with my hand, so used two small screwdriver under the metal tabs which hold the lens in place, the metal holder came out with the lens. Once the lens is r ... Read more emoved, simply pull out the old bulb and, either while wearing surgical gloves or holding the bulb with a cloth (do NOT allow bare skin to touch the bulb or you will be replacing it again sooner rather than later), push the new bulb's pins into the socket. The lens then is simply pushed back into place.

Purchased 2 piece broiler pan from this site

If doing this for the first time, it's harder to replace than described by others.

Start by removing the oven door. Reach in to unscrew the two screws that hold the sensor in place on the back wall of the oven. I was working on the upper oven of a double wall oven and found it more comfortable to sit on a tall bar stool whil ... Read more e working. Pull the sensor partially out and you will see the connector wire running through the sensor opening. The sensor connector plug is too deep into the oven to reach with fingers or any tool. Next unscrew the 6" round heat circulator fan just below the sensor on the back wall of the oven. Pull the fan partially out and you will see the plug for the temp sensor directly behind. You may have to push some of the insulation of out of way. Unplug the old sensor and pull it back out directly through the sensor opening. Take the new sensor and thread it in through the opening and plug it in. Reinstall the circulator fan and then screw the new sensor in place. This should complete the temp sensor replacement.

Removed oven, removed top cover, replaced thermal fuse, removed back cover, replaced fuse in rear. Both fuses went bad due to self clean cycle. I feel like I almost burnt my house down and the fuses did their job. No more self cleaning for me

I didn't. Don't know how to get to light bulb to change it for this specific model

We got on YouTube and watched a couple of repair videos. We decided that the repair was something we would try to tackle ourselves.

1. Turn off the breaker.
2. Remove all of the oven racks.
3. Remove the oven door as per users manual.
4. Remove two 1/4" screws on the plate holding the broil element
to the back of the oven.
5.. Remove two 1/4" screws in the front of the element holding
reflective plate and element toward th ... Read more e front of the oven.
6. Carefully pull the element out enough to remove the wire spade
contacts with from the rear of the element with long nosed pliers
being careful not to let the wires go behind the rear oven cavity.
7. Element and top reflective plate assembly can now be removed
from the oven.
8. The old element is removed from the reflective plate by removing
four 1/4" screws.
9. Install the new element on the plate and reverse the procedure to
reinstall the completed assembly into the oven.
10 Reinstall the door and racks, turn on the power and test.

This was easy to replace. I removed the oven door for easier access to the back of the oven. Removed two Phillips head screws that hold the burner element and disconnected the two wires on the burner element. I could have left the wires connected, but it was easier to extract the sensor with it out of the way. The only difficulty was fish ... Read more ing the sensor connector out through the hole. After that, easy peezy.

I removed the 2 screws holding the sensor in the back of the oven and pulled the wires out. The connector got hung up in the insulation. Rather than pulling too hard, I loosened up the heating element plate and screws and pulled the whole plate out an inch or so so I could work the connector through the insulation. I forgot to shut off ... Read more the power. When I put the sensor on, I got the same error. I briefly shut off the power at the breaker and turned it back on. The clock on the oven did not reset. It still didn't work. So I took the whole thing out, shut off the power, reconnected it, turned the power back on, reset the clock, and it worked! Should have turned the power off first and I wouldn't have had to do it twice.

REMOVED PANEL COVER [ 4 SCREWS]
UNSCREWED 2 SCREWS ON LATCH DOOR
ON THIS MODEL THE PART WAS IN TOO TIGHT OF QUARTERS SO I HAD TO LOOSEN A TOP PANEL SO I COULD RAISE PART HIGH
ENOUGH TO RELEASE IT FROM A CATCH AT THE BACK OF THE PART. PUSH PART BACK, RAISE AND PULL FORWARDS.
REMOVED 4 WIRES ONE AT A TIME AND ATT ... Read more ACHING TO NEW PART. REPLACED PART, TIGHTEN TOP PANEL AND REPLACED PANEL COVER.

NOT BAD FOR A 91 YEAR OLD