KOSE500 - Instructions

REMOVED PANEL COVER [ 4 SCREWS]
UNSCREWED 2 SCREWS ON LATCH DOOR
ON THIS MODEL THE PART WAS IN TOO TIGHT OF QUARTERS SO I HAD TO LOOSEN A TOP PANEL SO I COULD RAISE PART HIGH
ENOUGH TO RELEASE IT FROM A CATCH AT THE BACK OF THE PART. PUSH PART BACK, RAISE AND PULL FORWARDS.
REMOVED 4 WIRES ONE AT A TIME AND ATT ... Read more ACHING TO NEW PART. REPLACED PART, TIGHTEN TOP PANEL AND REPLACED PANEL COVER.

NOT BAD FOR A 91 YEAR OLD

I tryed to remove the sensor from the oven by removing the screws inside the oven. Unfortunatly, the plug for the sensor would not reach the inside of the oven. I had to remove the oven from the wall and remove the back cover to ac3ess the sensor wiring.
After that it was a snap.

removed existing racks; slide new rack over both sides to the back.

Didn't need sensor replaced. After turning the breaker switch back on oven appeared to be working fine.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

removed unit from cabinet tested switch it was OK checked wiring and found shorted out wire leading to switch. cut out bad section and spliced wire back together
problem solved

Very easy. Take out the screws with the supplied wrenches and install new chrome. 5 minute job.

Easy peasy. After using the shop vac to remove the glass fragments, 8 Phillips head screws were all that I had to remove. The schematic on this website was close enough, but I recommend taking pictures as you disassemble.

Caveat: I took it apart several days before I got the part, so I had plenty of time for my forgetter to wo ... Read more rk.

Put cribbing on a dolly, slid the oven out of the cabinet. Unfastened the upper broiler element allowing removing temperature sensor screw. Removed all the back panels and pushed the temperature sensor wire clip thru to the oven, Pushed the new emperature sensor wiring back thru the hole to the back. Removed and repalaced the blower re co ... Read more nnected the wire harnes for the blower and temperature sensor.. Replaced all the back panels and slid the oven back into the cabinet. Re attached the temperature swensor and re fastioned the upper broiler element. All went well and am glad the sales lady sent the how to videos. The videos were foir a different model but were essentially the same.

Taking off the glass lense for the light bulb was harder than I thought. It unscrews counterclockwise, but it was very hard to get off. It would not turn. I ended up using connector pliers I use for work, that has rubber jaws. The lense unscrewed very easy with it. Light also unscrews out. PartSelect.com is the only way to go to buy parts ... Read more for appliances. It is simple, even has the illustrated parts catalog. And it saves a lot of time and gas, driving around looking for the part!!. PartSelect came through again.

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

ordered new broiler pan

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh ... Read more t bulb in was not the problem.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes