KOCE507EB - Instructions

Removed oven, removed top cover, replaced thermal fuse, removed back cover, replaced fuse in rear. Both fuses went bad due to self clean cycle. I feel like I almost burnt my house down and the fuses did their job. No more self cleaning for me

I didn't. Don't know how to get to light bulb to change it for this specific model

We got on YouTube and watched a couple of repair videos. We decided that the repair was something we would try to tackle ourselves.

The replacement turntable we received was an exact duplicate of the original. It was as easy as rinsing the new turntable, taking the old turntable out and putting the new one in.

Ordered a new one, put it in place in less than one minute.

I removed the 2 screws holding the sensor in the back of the oven and pulled the wires out. The connector got hung up in the insulation. Rather than pulling too hard, I loosened up the heating element plate and screws and pulled the whole plate out an inch or so so I could work the connector through the insulation. I forgot to shut off ... Read more the power. When I put the sensor on, I got the same error. I briefly shut off the power at the breaker and turned it back on. The clock on the oven did not reset. It still didn't work. So I took the whole thing out, shut off the power, reconnected it, turned the power back on, reset the clock, and it worked! Should have turned the power off first and I wouldn't have had to do it twice.

1. Turn off the breaker.
2. Remove all of the oven racks.
3. Remove the oven door as per users manual.
4. Remove two 1/4" screws on the plate holding the broil element
to the back of the oven.
5.. Remove two 1/4" screws in the front of the element holding
reflective plate and element toward th ... Read more e front of the oven.
6. Carefully pull the element out enough to remove the wire spade
contacts with from the rear of the element with long nosed pliers
being careful not to let the wires go behind the rear oven cavity.
7. Element and top reflective plate assembly can now be removed
from the oven.
8. The old element is removed from the reflective plate by removing
four 1/4" screws.
9. Install the new element on the plate and reverse the procedure to
reinstall the completed assembly into the oven.
10 Reinstall the door and racks, turn on the power and test.

This was easy to replace. I removed the oven door for easier access to the back of the oven. Removed two Phillips head screws that hold the burner element and disconnected the two wires on the burner element. I could have left the wires connected, but it was easier to extract the sensor with it out of the way. The only difficulty was fish ... Read more ing the sensor connector out through the hole. After that, easy peezy.

We bought a really nice microwave for about 1/3rd of the MSRP, but it was an open box item and when we got it home we found that it was missing a bracket on the inside of the microwave. We were able to replace the bracket easily thanks to partselect.com.

Should be about 1 5/8 inch with 3/8 inch prongs. Sent bulb won’t fit.
JennAire book showed
Part 74004458-halogen bulb part PS 11765655 was substituted.
I paid additional shipping so my son could install when here. My husband and I are 79 and unable to bend into the oven.
I need the correct part
where do I r ... Read more eturn the unopened $29.95 bulb for credit on my card and receive the correct one?????
Carolyn Sanders 817-319-6581
Order 21938961

REMOVED PANEL COVER [ 4 SCREWS]
UNSCREWED 2 SCREWS ON LATCH DOOR
ON THIS MODEL THE PART WAS IN TOO TIGHT OF QUARTERS SO I HAD TO LOOSEN A TOP PANEL SO I COULD RAISE PART HIGH
ENOUGH TO RELEASE IT FROM A CATCH AT THE BACK OF THE PART. PUSH PART BACK, RAISE AND PULL FORWARDS.
REMOVED 4 WIRES ONE AT A TIME AND ATT ... Read more ACHING TO NEW PART. REPLACED PART, TIGHTEN TOP PANEL AND REPLACED PANEL COVER.

NOT BAD FOR A 91 YEAR OLD

Part arrived in timely manner and placed it in microwave oven.

Set the new one inside the microwave

The part is pushed against the ceiling into an opening and then turned 90 degree. That is is.

Didn't need sensor replaced. After turning the breaker switch back on oven appeared to be working fine.