Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Open the carton and install turntabe glass tray.
2 of 3 peoplefound this instruction helpful.
Roger from LYMAN, ME
Very Easy
Less than 15 mins
Fool proof.
Was this helpful?
Thank you for voting!
upper oven of wall oven would not heat suspected high temp limit switch
2 of 3 peoplefound this instruction helpful.
William from Carbondale, CO
Really Easy
15 - 30 mins
Nutdriver
removed unit from cabinet tested switch it was OK checked wiring and found shorted out wire leading to switch. cut out bad section and spliced wire back together problem solved
Was this helpful?
Thank you for voting!
Inner door glass EXPLODED while preheating!
1 personfound this instruction helpful.
J.M. from Royal, AR
Really Easy
15 - 30 mins
Screw drivers
Easy peasy. After using the shop vac to remove the glass fragments, 8 Phillips head screws were all that I had to remove. The schematic on this website was close enough, but I recommend taking pictures as you disassemble.
Caveat: I took it apart several days before I got the part, so I had plenty of time for my forgetter to wo
... Read morerk.
Read less
Was this helpful?
Thank you for voting!
I broke the glass cooking tray when instaling my oven microwave combo
2 of 4 peoplefound this instruction helpful.
Jeff from Baytown, TX
Really Easy
Less than 15 mins
I put the tray in the microwave???? Pretty easy.
Was this helpful?
Thank you for voting!
The ceramic hanger that holds up the element for the convection over broke
1 personfound this instruction helpful.
Joyce from Conyers, GA
Very Easy
Less than 15 mins
Took about 10 seconds... turn the new ceramic holder sideways, push up in the hole, bring the element up to position and twist the ceramic piece 45 degrees into place to hold element. That's it!!! Very simple....
Was this helpful?
Thank you for voting!
Temperature not holding and blower squeeling
1 personfound this instruction helpful.
Tom from BELLEVUE, WA
Easy
1- 2 hours
Nutdriver, Screw drivers
Put cribbing on a dolly, slid the oven out of the cabinet. Unfastened the upper broiler element allowing removing temperature sensor screw. Removed all the back panels and pushed the temperature sensor wire clip thru to the oven, Pushed the new emperature sensor wiring back thru the hole to the back. Removed and repalaced the blower re co
... Read morennected the wire harnes for the blower and temperature sensor.. Replaced all the back panels and slid the oven back into the cabinet. Re attached the temperature swensor and re fastioned the upper broiler element. All went well and am glad the sales lady sent the how to videos. The videos were foir a different model but were essentially the same.
We ordered element support 3 times and all three times it came broken. The part is made of porcelain and is fragile , representative asked warehouse to pack it in the box and part still came in envelope. Requested refund and ordered directly from factory.
Was this helpful?
Thank you for voting!
Grill support broke. Sounds like a common problem based on other’s comment.
1 personfound this instruction helpful.
Andrew from LAKEVILLE, MN
Really Easy
Less than 15 mins
Turn the grill support 90 degrees to the opening in ceiling of micro. Insert then turn back 90 degrees so the support is in-line with the slot. Hang the wire on the support. Hours of worry over what this was gonna cost me to get repaired, then a 45 second fix costing only 29 bucks.
Was this helpful?
Thank you for voting!
Broken mounting bracket for coils in convection microwave.
4 of 10 peoplefound this instruction helpful.
Larry from Fernandina Beach, FL
Really Easy
Less than 15 mins
Very easy, fit perfectly.No tools required.
Was this helpful?
Thank you for voting!
Micro Wave Steamer
1 personfound this instruction helpful.
James from MIAMI, FL
Very Easy
Less than 15 mins
I spoke to Daily via the phone and I ordered a new steamer since my original steamer cracked over a period of time. No installation, no problems I just recently used it and works perfectly! Thank You!
Was this helpful?
Thank you for voting!
INTERIOR OVEN LIGHT
3 of 7 peoplefound this instruction helpful.
Gary from WALTON, KY
Really Easy
Less than 15 mins
Screw drivers
EASILY REMOVED GLASS COVER INSIDE OVEN AND REMOVED SMALL HALOGEN LIGHT BULB. RECEIVED REPLACED WITHIN TWO DAYS OF ORDER AND REPLACED BULB AND GLASS COVER IN ABOUT 10 MINUTES. MOST DIFFICULTY WAS HAVING TO BEND DOWN TO REACH INSIDE OF OVEN TO LOCATE POSITION TO INSERT BULB.
Was this helpful?
Thank you for voting!
Missing turntable
1 personfound this instruction helpful.
Kristen from Yorba Linda, CA
Very Easy
Less than 15 mins
Ordered the part and was extremely pleased with how quickly it shipped and also the packaging was extremely secure. Will definitely purchase from this site again.
Was this helpful?
Thank you for voting!
Changed out red medallions for chrome
1 personfound this instruction helpful.
Timothy from AUBURN, MA
Very Easy
Less than 15 mins
Very easy. Take out the screws with the supplied wrenches and install new chrome. 5 minute job.
Was this helpful?
Thank you for voting!
Old microwave glass tray shattered while warming a hard-boiled egg.
1 of 2 peoplefound this instruction helpful.
Raymond from HINSDALE, IL
Very Easy
Less than 15 mins
I took the new tray out of the box and placed it in the microwave oven.. No tools needed.
Was this helpful?
Thank you for voting!
broken glass dish for microwave
1 of 2 peoplefound this instruction helpful.
Janet from Concord, CA
Really Easy
Less than 15 mins
no repair needed - ordered part, came within 3 days - very satisfied
My Orders
