- Home
- KMBP100ESS20
- Instructions
KMBP100ESS20 KitchenAid Microwave - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Scratches in Surface
83 of 227 people
found this instruction helpful.
-
Michelle from Richardson, TX
- Really Easy
- Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Burnt out Microwave Lamp
9 of 11 people
found this instruction helpful.
-
Donald from SOLVANG, CA
- Difficult
- 30 - 60 mins
-
Screw drivers
IMPORTANT: DO NOT TOUCH THE REPLACEMENT LAMP WITHOUT WEARING CLEAN GLOVES. FILM OR FINGER PRINTS ON THE LAMP GLASS WILL CAUSE PREMATURE FAILURE OF THE LAMP.
Remove the 4 screws on right and left mounting rails that hold the unit to the kitchen cabinet.
Remove the oven door
Remove the chrome oven vent strip below the ... Read more oven door. This allows a pry point beneath the combo microwave oven assembly to lift up the unit while pulling it out. (Assembly weighs 250 pounds)
Pull the unit out from the cabinet housing about 2-3 inches to reveal the right and left sides and the 4 screws holding the the control panel.
Remove the 4 control panel screws and pull off the face of the control panel
Remove the 2 harness connectors and the ground wire holding the control panel to the unit.
Unclip the circuit board above the lamp connector and slide it back out of the way. The lamp is now accessible.
Remove the lamp spring holding the lamp to the cabinet.
Remove the old lamp
Install the new lamp using clean gloves
Reassemble in reverse order.
Remove the 4 screws on right and left mounting rails that hold the unit to the kitchen cabinet.
Remove the oven door
Remove the chrome oven vent strip below the ... Read more oven door. This allows a pry point beneath the combo microwave oven assembly to lift up the unit while pulling it out. (Assembly weighs 250 pounds)
Pull the unit out from the cabinet housing about 2-3 inches to reveal the right and left sides and the 4 screws holding the the control panel.
Remove the 4 control panel screws and pull off the face of the control panel
Remove the 2 harness connectors and the ground wire holding the control panel to the unit.
Unclip the circuit board above the lamp connector and slide it back out of the way. The lamp is now accessible.
Remove the lamp spring holding the lamp to the cabinet.
Remove the old lamp
Install the new lamp using clean gloves
Reassemble in reverse order.
Read less
Was this helpful?
Thank you for voting!
Bulb entirely to small and unopened
3 of 3 people
found this instruction helpful.
-
Carolyn from BURLESON, TX
- Very Difficult
- More than 2 hours
Should be about 1 5/8 inch with 3/8 inch prongs. Sent bulb won’t fit.
JennAire book showed
Part 74004458-halogen bulb part PS 11765655 was substituted.
I paid additional shipping so my son could install when here. My husband and I are 79 and unable to bend into the oven.
I need the correct part
where do I r ... Read more eturn the unopened $29.95 bulb for credit on my card and receive the correct one?????
Carolyn Sanders 817-319-6581
Order 21938961
JennAire book showed
Part 74004458-halogen bulb part PS 11765655 was substituted.
I paid additional shipping so my son could install when here. My husband and I are 79 and unable to bend into the oven.
I need the correct part
where do I r ... Read more eturn the unopened $29.95 bulb for credit on my card and receive the correct one?????
Carolyn Sanders 817-319-6581
Order 21938961
Read less
Was this helpful?
Thank you for voting!
Micro Wave Steamer
1 person
found this instruction helpful.
-
James from MIAMI, FL
- Very Easy
- Less than 15 mins
I spoke to Daily via the phone and I ordered a new steamer since my original steamer cracked over a period of time. No installation, no problems I just recently used it and works perfectly! Thank You!
Was this helpful?
Thank you for voting!
INTERIOR OVEN LIGHT
3 of 7 people
found this instruction helpful.
-
Gary from WALTON, KY
- Really Easy
- Less than 15 mins
-
Screw drivers
EASILY REMOVED GLASS COVER INSIDE OVEN AND REMOVED SMALL HALOGEN LIGHT BULB.
RECEIVED REPLACED WITHIN TWO DAYS OF ORDER AND REPLACED BULB AND GLASS COVER IN ABOUT 10 MINUTES.
MOST DIFFICULTY WAS HAVING TO BEND DOWN TO REACH INSIDE OF OVEN TO LOCATE POSITION TO INSERT BULB.
RECEIVED REPLACED WITHIN TWO DAYS OF ORDER AND REPLACED BULB AND GLASS COVER IN ABOUT 10 MINUTES.
MOST DIFFICULTY WAS HAVING TO BEND DOWN TO REACH INSIDE OF OVEN TO LOCATE POSITION TO INSERT BULB.
Was this helpful?
Thank you for voting!
Changed out red medallions for chrome
1 person
found this instruction helpful.
-
Timothy from AUBURN, MA
- Very Easy
- Less than 15 mins
Very easy. Take out the screws with the supplied wrenches and install new chrome. 5 minute job.
Was this helpful?
Thank you for voting!
Oven light burnt out
1 of 3 people
found this instruction helpful.
-
Todd from TRENTON, MI
- Very Easy
- Less than 15 mins
Took off outer cover Popped out old bulb put in new one
Replaced cover
Replaced cover
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people
found this instruction helpful.
-
Howard from Boynton Beach, FL
- Easy
- 30 - 60 mins
-
Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol
... Read more
oring refer handles. Thank you
Read less
Was this helpful?
Thank you for voting!