KLRF15XTAL00 Whirlpool Refrigerator - Instructions

First I watched PartSelect videos that Bing rounded up describing the repair. I saw how to remove an ice maker, the back panel of the freezer, and remove and replace the fan and motor. The order was made on Wednesday, arrived Thursday and installed Friday. I took the time to clean everything while it was apart. The refrigerator is run ... Read more ning like a new one, quietly and colder than before. It felt good to be able to do it my self. My wife was sure the refrigerator was going to stop running, but I proved her wrong.

Removed the old fan; cut the wire and spliced in the new fan and reassembled. A little over one hour. Refrig is working perfectly now with lower settings. It is definitely off much more than on now.

just had to remove the fan motor the hard thing is getting down to it

This was an easy part to find thanks to its universality. The only difficulty was the electric snap-on connection - had to use the old one and tie the wires to the new motor - that was easy. Hardest part was the new screws to mount to bracket weren't long enough. Had to find one in my screw jar to match threads that was long enough. W ... Read more orks Great!!!

Well I could what laid on the floor and replaced it but I didn't I emptied refrigerator laid it over change the motor then stood it back up actual work about three hours

The video of the repair is a helpful guide, but my refrigerator has the compressor very close to the condenser fan motor. With the compressor comes the copper tubing that is all in the way. I had to carefully bend them now and then to allow me to get my hands in position. The how to is easy, but the working with tools in cramped quarters ... Read more was difficult. I think my Maytag side by side model makes for this job to be difficult, maybe yours may not be so bad. I took a couple of hours to complete. After the first hour, I covered the bare wires, and plugged the frig back in so it could do some cooling. I placed a small in front on the condenser to blow across it. Had a little break, then finished the job.

removed condenser fan -located behind refrigerator next to compressor, Not much clearance to work, there are 3 screws to remove from condensing motor,sounds easy but clearance is lacking to remove them ,(takes alot of PATIENCE). Then you have to remove the fan blades to be able to get clearance to remove motor!! I wouldn't reccommend tryi ... Read more ng this repair unless you are a pro.

Pulled refridgerator forward away from the wall. Remove the cardboard back behind the appliance.I saw that the condenser fan motor was not working. Unplugged the appliance from the electrical outlet. Removed a 3 wire plug from the condenser fan motor. Remove 3 screws (with a nut driver) which held the condenser fan motor in place. Remove ... Read more the condenser fan motor from the appliance. Looked up the part needed for repair using the appliance model number. Found which part was applicable for the appliance. Placed the order from Price Select on a Monday morning and recieved the part 2 days later on Wednesday via FedEx. The item shipped was a 2 wire condenser fan motor. Read the instructions that came with the part. Using wire cutters, cut the old 3 wire plug. The center wire is a green and yellow striped wire. Use the same colored wire that is also shipped in the box and has connectors on both ends. Cut one of the connectors off and use the wire strippers to remove plastic wire coating. Connect both ends from the appliance and the green and yellow wire that was shipped. Use a wire nut (also shipped in the box) to connect the wires. You will have 2 black wires left on the new condenser fan motor that need to be connected to the appliance. You should have an orange colored wire and another wire that is black with a white stripe. Connect one wire from the new fan motor to the orange wire and use a wire nut to attach both wires together. Use the other black wire from the new fan motor to the black/white striped wire from the appliance. Use the wire nut to attach both those wires. Place the new condenser fan motor back in the appliance using the screws that come with the motor. Attach the green and white wire with the connector on the end to one of the 3 screws that hold the motor in place and secure the screws. Use the electical tape to hold the wires all together and away from the fan motor. Plug the appliance into the outlet. You can see the condenser fan motor working properly. Note that when connecting the 2 black wires from the new condenser fan motor to the orange and the black/white wire from the appliance, for my appliance, it did not matter which wires were connected as the fan motor was a clockwise motor. Place the cardboard appliance backing, back on to the appliance and push the refridgerator back in place. Allow about 5-6 hours to get the freezer to between 0-5 degrees. The refidgerator should be between 34-38 degrees and will take a little longer to get to that projected temp.

opened box,read directions,took out bad motor,installed new one.PRESTO CHANGO way to go.

Unplugged freezer, removed lower shelving, removed panel covering the evaporator motor. Unpluged three wires connected to fan assem and removed. Did not install new wiring that came with kit but installed new motor/fan and reconnected existing wiring. Problem gone!

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Pla ... Read more ce the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.

Remove freezer shelves, panel, and change fan.

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

Mine was alittle different than the online instructions. 1. I removed the motor. 2. I took the fan off the old motor and cut the wires about 3" back from old motor. 3. Mounted the new fan on bracket and put the fan on the new motor. 4.connected wires that were cut and used wire nuts to connect. 5. Mounted bracket and motor/fan to unit and ... Read more it works like its brand new. Thank you PartSelect!

I knew the repair wasn't difficult. It was a matter of finding the replacement part. Luckily, I found the part via the internet on your site. Lucky for me, there was an installation video!! These videos are worth 1000 bucks!! Never have encountered a site with installation videos before. It gave me complete insight as to how the job was ... Read more sequenced. I'm a very visual person, so videos are the perfect helper for me. With fewer and fewer affordable local service companies around to fix problems like mine, your site gave me the complete confidence to easily switch out the condensor fan. I completed the repair for about $63.00. Your site ROCKS! Keep up the repair videos because they are awesome and extremely helpful. I felt like your pricing was competitive for this item. Thanks again!!