KHWS02RWH1 KitchenAid Washer - Instructions

Real easy , the baffle goes in only one way , use the others as guide as too which side the taller end goes.
With one hand pushing in the center of the back of the basket , pushing back , simply place and slide baffle towards you with other hand , there will be a crisp snap as it slide in to place.

Removed the old hoses and screwed on the new hoses.

Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 ... Read more people
connect bellows to door with spring clip

I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.

I replaced the hose and reinstalled the panels and I was do ... Read more ne.

It was fast and pretty easy to do.

Removed the three screws in the back took off the top and swamped out the part. I recommend that the inlet valve is checked periodically by removing the hoses to see if there's any build up on the filter.

Followed internet instructions

We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.

Unplugged power cord, turned off both water valves on the wall, Disconnected the water hoses o the back where they are attached to the water inlet valve. Note: there will likely be some water left in the hoses. Then removed top lid of washer (this is a front load washer) by removing the 3 nut screws on the back of the lid and sliding it t ... Read more o the back and lifting off.. Disconnected the small hose that is attached to the water inlet valve by squeezing the hose clamp and sliding the hose off. Removed the 4 wires connected to the water inlet valve (marked each one with a number in order) then removed the Phillips head screw on the back of the machine holding the water inlet valve, sliding the valve to the right, . Removed valve, and replaced with new one, and re-installed by reversing order of removal.

place new baffle over slots in drum; move toward back of drum and snap in to place pressing down and moving toward front of drum

firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.

Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into plac ... Read more e and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.

Easily. 4 Screws. 2 Clamps.

Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump w ... Read more ith the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good

Lined the new one up with one hand;(cold beer in the other), snapped it to place, finished.