KHS - Overview

The Fuel Tank Grommet is a 1-inch, black, rubber part. It attaches to the fuel tank so you can run your fuel lines through it, and is rated as "Easy" to install by most of our customers. If worn or damaged, it will begin to leak fuel, and must be replaced. Refer to your make, model and diagrams to ensure you're choosing the right part.

The Fuel Cap Assembly, is a black, plastic cap that keeps fuel inside the tank, and debris out. If broken, fuel will begin leaking out and it must be replaced. Installation is rated as "Easy", the part simply attaches on top of the fuel tank. Refer to your make, model, and diagram to ensure this is the correct part.

The Primer, or priming pump, is a plastic part that attaches to the carburetor. It's rated as "Easy" to install by most of our customers. This part is used to pump fuel from the fuel tank to the carburetor or to start the engine. If damaged, it will no longer pump fuel. It may also be physically, noticably broken. Replace this part if dam...Read moreaged. Check your make, model and diagrams to ensure you're choosing the right part.

The fuel filter clamp, is a silver, individually sold, metal part, used to secure the fuel line to the fuel filter. It attaches to the fuel filter and if broken, typically due to fatigue or damage, it should replaced. Installation is rated as "Easy" and requires Pliers and a Screwdriver. When removing the fuel line to remove the old clamp...Read more, make sure you have a bucket to catch the fuel. Refer to your make, model, and diagram to ensure you're choosing the right part.

The Breather allows air to enter the tank, so no vacuum is created as the fuel level drops, which would prevent the flow of fuel to the carburetor.It seals in the gas emissions and fuel at the same time. It is a metal and rubber part, sold individually, rated as "Easy" to install. If damaged, fuel may start leaking from it, and it must be...Read more replaced. The part is attached inside of the fuel cap. Refer to your make, model and diagrams to ensure you're choosing the right part.

The Fuel Tank Cap and Breather is an assembly made up of black plastic parts. You'll know if you need a new one if fuel is leaking, and this appears to be the source. This can happen due to normal wear, fatigue, and damage. This kit is rated as "Easy" to install and attaches to the fuel tank. Refer to your make, model and diagrams to ensure you're choosing the right part.

This fuel filter helps to ensure the fuel that goes into the engine is free of any contaminants. It is a genuine OEM sourced replacement part that is specially made for Kawasaki lawn and garden equipment. Filters over time may get clogged restricting the fuel flow, if this happens the filter would need to be replaced. This item consists of a metal frame with a felt filter material and it is sold individually.

This 2-cycle in-tank fuel filter is a component in your lawn equipment that ensures clean fuel reaches the engine by filtering out impurities and debris. It is made of durable metal and high-quality felt and is typically located in the fuel lines. A clogged or cracked filter can cause engine sputtering and idling issues, leading to fuel f...Read morelow problems and potential engine damage. Additionally, impurities in the fuel can damage the engine. To install a new filter, first turn your machine off and allow the engine to cool. Use pliers or a wrench to disconnect the fuel lines. Slide out the old fuel filter, taking care to remove any mounting brackets or holders if necessary. This authentic OEM filter is sold individually.

It is made of a felt material and is sold individually. The air filter element fits between the cap and the baffle. A screwdriver might be necessary during the installation of this part. This item may become dirty over time and will need to be replaced. This is an OEM from Kawasaki for use in engines, edgers, and trimmers.

This Element Air Filter is used to prevent contaminents from entering the carburetor and engine causing damage. it is an OEM part that is installed inside the air cleaner housing, and is rated "Easy" to install by most customers. Installation will only require a screwdrier. If the filter has become clogged, your engine will have fuel and ...Read moreperformance problems. If this happens, your filter will need to be cleaned or replaced. Refer to your make, model, and diagrams to ensure this is the right filter for you.

This is an OEM part sourced directly from the manufacturer. The carburetor priming pump is found in Kawasaki backpack leaf blowers and small engines. This part is made of high-quality plastic, and is used to inject priming fuel into the carburetor. This item is provided as an individual replacement part.